Sony CPD-G200 Specifications, Self-diagnosis function, If the 1 power indicator is green, Crt

Page 16

Self-diagnosis function

This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer, the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard.

MENU

RESET

1 (power) indicator

If the 1 (power) indicator is green

1Disconnect the video input cable or turn off the connected computer.

2Press the 1 (power) button twice to turn the monitor off and then on.

3Move the control button ,for 2 seconds before the monitor enters power saving mode.

MENU

If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cable and check the condition of your computer.

If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition.

If the 1 (power) indicator is flashing orange

Press the 1 (power) button twice to turn the monitor off and then on.

If the 1 (power) indicator lights up green, the monitor is working properly.

If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board.

Specifications

CRT

0.24 mm aperture grille pitch (center)

 

17 inches measured diagonally

 

90-degree deflection

 

FD Trinitron

Viewable image size

Approx. 327 × 243 mm (w/h)

 

(12 7/8 × 9 5/8 inches)

 

16.0" viewing image

Resolution

 

Maximum

Horizontal: 1600 dots

 

Vertical: 1200 lines

Recommended

Horizontal: 1024 dots

 

Vertical: 768 lines

Standard image area

Approx. 312 × 234 mm (w/h)

 

(12 3/8 × 9 1/4 inches)

Deflection frequency*

Horizontal: 30 to 96 kHz

 

Vertical: 48 to 120 Hz

AC input voltage/current

100 to 240 V, 50/60 Hz, Max. 1.7 A

Power consumption

130 W

Dimensions

Approx. 404 × 413.5 × 419.5 mm (w/h/

 

d) (16 × 16 3/8 × 16 5/8 inches)

Mass

Approx. 20 kg (44 lb 1 oz)

Plug and Play

DDC1/DDC2B/DDC2Bi/GTF

Supplied accessories

See page 6

*Recommended horizontal and vertical timing condition

•Horizontal sync width should be more than 1.0 µsec.

•Horizontal blanking width should be more than 3.0 µsec.

•Vertical blanking width should be more than 500 µsec.

Design and specifications are subject to change without notice.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents
Trinitron Color Computer Display Importante HinweiseTable of Contents Precautions InstallationMaintenance TransportationFront Identifying parts and controlsRear Setup Connect the power cordConnecting to an IBM PC/AT or compatible Computer Connecting to a Macintosh or compatible computerTurn on the monitor and computer Selecting the on-screen menu language LangIf no picture appears on your screen Press the center of the control buttonCustomizing Your Monitor Displaying the current input signalNavigating the menu Adjusting the brightness and contrast Adjusting the centering of the picture CenterAdjusting the size of the picture Size Using the control buttonAdjusting the shape of the picture Geom Adjusting the color of the picture ColorAdjusting the convergence Conv Enlarging or reducing the picture ZoomAdditional settings Option Adjusting the moireDegaussing the screen Changing the menu’s positionResetting the adjustments Helpful hints and information HelpTechnical Features TroubleshootingTrouble symptoms and remedies Symptom Check these items No picturePicture flickers, bounces Oscillates, or is scrambledSymptom Check these items Picture is ghosting Power is turned onPicture is not centered or sized ProperlySpecifications If the 1 power indicator is greenIf the 1 power indicator is flashing orange Self-diagnosis functionInstallation Table des MatièresPrécautions EntretienTransport Utilisation du support pivotantAvant Identification des composants et des commandesArrière Installation 1re étape Raccordez le moniteur à votre ordinateur2e étapeBranchez le cordon ’alimentationAppuyez au centre de la manette de commande Sélection de la langue d’affichage des menus LangSi aucune image n’apparaît à l’écran English AnglaisPersonnalisation de votre moniteur Affichage du signal d’entrée en coursPilotage par menus Utilisation de la manette de commande Réglage de la luminosité et du contrasteRéglage du centrage de l’image Centre Réglage de la taille de l’image TailleAgrandir ou réduire l’image Zoom Réglage de la forme de l’image GeomRéglage de la couleur de l’image Coul Réglage de la convergence ConvVerrouillage des commandes Réglages supplémentaires OptionDémagnétisation de l’écran Réglage du moiréConseils et informations utiles Aide Réinitialisation des réglagesCaractéristiques techniques DépannageModes présélectionné et utilisateur Fonction d’économie d’énergieSymptômes et remèdes Symptôme Vérifiez Pas d’imageSymptôme Vérifiez ’image est floue Des images fantômesApparaissent ’image n’est pas centrée ou deFonction d’autodiagnostic SpécificationsSi l’indicateur 1 alimentation est allumé en vert Si l’indicateur 1 alimentation clignote en orangeÍndice InstalaciónPrecauciones Parte frontal Identificación de los componentes y los controlesParte posterior Instalación Paso 1 Conexión del monitor al ordenadorPaso 2 Conexión del cable de alimentación Conexión a un ordenador IBM PC/AT o compatiblePaso 3 Encendido del monitor y del ordenador Selección del idioma de los menús en pantalla LangSi las imágenes no aparecen en pantalla Pulse el centro del botón de controlNavegación por el menú Personalización del monitorVisualización de la señal de entrada actual Ajuste del brillo y del contraste Ajuste del centrado de la imagen CentroAjuste del tamaño de la imagen Tamaño Uso del botón de controlAmpliación o reducción de la imagen Zoom Ajuste de la forma de la imagen GeomAjuste del color de la imagen Color Ajuste de la convergencia ConvDesmagnetización de la pantalla Ajuste del muaréCambio de la posición del menú Bloqueo de los controlesSugerencias e información útiles Ayuda Restauración de los ajustesSolución de problemas Características técnicasProblemas y soluciones Problema Compruebe lo siguiente Ausencia de imagenLa imagen parpadea, se ondula Oscila o aparece codificadaProblema Compruebe lo siguiente Aparecen imágenes fantasma La imagen aparece descentrada oCon un tamaño incorrecto Los bordes de la imagen aparecenEspecificaciones Función de autodiagnósticoSi el indicador 1 alimentación está iluminado en verde Si el indicador 1 alimentación parpadea en naranjaAppendix Preset mode timing tableTCO’99 Eco-document Environmental requirements