Sony GDM-W900 Preset Modes, Selecting the Input Signal, Preset modes, User modes

Page 5

Preset Modes

Preset modes

The monitor has nine factory preset modes for true “Plug & Play” capability.

Table of preset modes

No. Resolution

Horizontal

Vertical

Graphic mode

 

(dots×lines)

Frequency

Frequency

 

1

640 × 480

31.5 kHz

60 Hz

VGA Graphic

2

720 × 400

31.5 kHz

70 Hz

VGA Text

3

1280 × 1024

80.0 kHz

75 Hz

VESA 1)

4

1600 × 1200

93.8 kHz

75 Hz

VESA

5

1920 × 1080

67.5 kHz

60 Hz

Sony

6

1920 × 1080

84.4 kHz

72 Hz

Sony

7

1600 × 1024

81.3 kHz

76 Hz

Sony

8

1920 × 1200

95.0 kHz

76 Hz

Sony

9

1920 × 1035

33.8 kHz

60 Hz

HDTV

1) VESA is a trademark of Video Electronics Standard Association.

User modes

When using a video mode that is not one of the preset modes, some fine tuning may be required to optimize the display to your preference. Simply adjust the monitor according to the adjustments instructions on pages 9 to 15. The adjustments will be stored automatically and recalled whenever that mode is used.

A total of 16 user-defined modes can be stored in memory. If a 17th mode is entered, it will replace the first.

For less common modes, and modes that may evolve in the future, the Digital Multiscan Technology of this monitor will perform all of the complex adjustments necessary to ensure a high quality picture for any timing in its frequency range. However, due to the wide variety of video boards on the market, it may be necessary for the user to fine tune the vertical/horizontal size and centering.

Recommended horizontal timing conditions

Horizontal sync width should be more than 0.8 µsec. Horizontal blanking width should be more than 2.7 µsec.

Note for Windows® 2) users

Check your video board manual or the utility program which comes with your graphic board and select the highest available refresh rate to maximize monitor performance.

2)Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

EN

F

D

Selecting the Input Signal

ES

I

This monitor has two signal input connectors and can connect two computers. When the power of both computers is on, select the signal you want to input as follows.

1Turn on power of the monitor and the computer.

2Select the input signal.

HD15 AUTO BNC

INPUT

To input the signal from the computer connected to the 5 BNC’s connector

Set the INPUT switch to BNC.

To input the signal from the computer connected to the HD15 connector

Set the INPUT switch to HD15.

If only one computer is connected or turned on

Set the INPUT switch to AUTO (center position). The input signal is automatically selected.

3If necessary, adjust the user controls according to your preference on pages 9 to 15.

When you set the INPUT switch to “AUTO”and connect computers to both connectors

If you turn on or restart the computer you want to input a signal from, or the computer is in power saving mode, the monitor may automatically select another computer’s signal. This is because no signal is input to the monitor at that moment. If this happens, select the signal using the INPUT switch.

For the customers using the Windows95

Even if you select SONY for the maker on the device select screen, the model name (GDM-W900) may not appear. In this case, select the DDC standard monitor.

J

5

Image 5
Contents Multiscan Hinweise Owner’s RecordIntroduction Table of ContentsPrecautions Connecting to the 5 BNC’s connector Connect the power cordConnections Connect the monitor to the computerSelecting the Input Signal Preset ModesPreset modes Table of preset modesFunctions of Controls Video input 1 connector HD15 AC in connectorVideo input 2 connector 5 BNC LanguageOperating the OSD Selecting the OSD LanguageChanging the OSD Position Selecting the normal mode Adjustments Normal modeAdjusting the picture Brightness Adjusting the picture contrastAdjusting the picture rotation Adjustments Normal mode Adjusting the picture CenteringAdjusting the picture size Adjusting the screen Adjusting the pincushionCanceling the Moire ConvergenceResetting all adjustment data Adjustments Normal mode Adjusting the color TemperatureResetting to the factory Preset levels Selecting the expert mode Adjustments Expert modeBrightness and contrast ¬ BrightnessFocus Adjustments Expert modeMoire ADJ Cancel MoireLanding DegaussControl Lock Function To cancel the control lockDegaussing the Screen Press the ?//button to select UnlockPower Saving Function Damper WirePower saving operation Plug & PlayUse of the Tilt- Swivel Input Signal Warning FunctionSpecifications Troubleshooting Troubleshooting Table of Contents Connections Preset Modes Functions of Controls Option OSD Selecting the OSD Language Adjustments Normal mode Adjustments Normal mode Adjusting the picture Centering Adjusting the pincushion Adjustments Normal mode Adjusting the color Temperature Adjustments Expert mode Adjusting the picture Adjusting the color Control Lock Function Plug & Play Input Signal Warning Function Troubleshooting Troubleshooting Précautions Table des matièresEntretien La source d’alimentation2e étape Branchez le cordon d’alimentation Raccordement1re étape Raccordez le moniteur à l’ordinateur Modes par défaut Sélection du signal d’entréeModes par défaut Modes utilisateurFonction des commandes Connecteur d’entrée vidéo 1 HD15 Connecteur ACConnecteur d’entrée vidéo 2 5 BNC Position OSDAppuyez sur la touche Option Pilotage par menusAppuyez sur la touche ¬ ./pour sélectionner Language Appuyez sur la touche ?//pour sélectionner la langue voulueSélection du mode normal Réglages mode NormalRéglage de la luminosité de ’image Réglage du contraste deRéglage du centrage de l’image Réglages mode NormalRéglage de la taille de l’image Réglage de la rotation de l’imageRéglage de l’écran Réglage de la distorsion en CoussinSuppression du moiré Appuyez sur la touche ScreenRéglage de la température de Couleur Réinitialisation aux valeurs De réglage par défautAlignement Réinitialisation de toutes les données de réglageRéglage de la luminosité et Du contraste de l’image Réglages mode ExpertSélection du mode expert Trapeze H Coussin H/ Corr CYL HCentrage H CentrageRéinitialisation des valeurs De réglage par défaut Réglage des couleursAppuyez sur la touche ?//pour sélectionner Deverr Pour désactiver le verrouillage des commandesDémagnétisation Fil d’amortissement Fonctionnement en mode ’économie d’énergieUtilisation du De signal d’entrée Support pivotantSpécifications Le message disparaît au bout d’environ 30 secondesDépannage Dépannage Sicherheitsmaßnahmen InhaltEinführung Schritt 2 Schließen Sie das Netzkabel an Anschließen des MonitorsSchritt 1 Schließen Sie den Monitor an den Computer an Voreingestellte Modi Auswählen des EingangssignalsVoreingestellte Modi BenutzermodiLage und Funktion der Bedienelemente Videoeingang 1 HD15 Netzeingang ACVideoeingang 2 5 BNC Language SeiteDrücken Sie die Taste Option Arbeiten mit der BildschirmanzeigeWählen Sie mit der Taste ¬ ./die Option Language aus Wählen Sie mit der Taste ?//die gewünschte Sprache ausAuswählen des normalen Modus Einstellungen NormalmodusEinstellen der Bildhelligkeit Einstellen des BildkontrastsEinstellen der Bildzentrierung Einstellungen NormalmodusEinstellen des Bildrotation Einstellen der BildgrößeEinstellen der Bildqualität Korrigieren der KissenverzeichnungKonvergenz Korrigieren des Moiré-EffektsEinstellen der Farbtemperatur Zurücksetzen der Werte auf die Werkseitigen EinstellungenFarbreinheit Zurücksetzen aller EinstellungenAuswählen des Expertenmodus Einstellungen ExpertenmodusEinstellen von Bildhelligkeit Und Kontrast ¬ HelligkeitBreite BildlageHöhe KISSEN/ H Kissen BALEinstellen der Farbe Entmagnetisierung TastensperrfunktionSo heben Sie die Tastensperre wieder auf Wählen Sie mit der Taste ?//die Option Freigb ausDämpfungsdrähte Plug and Play EnergiesparfunktionArbeitsweise der Energiesparfunktion AchtungTechnische Daten Störungsbehebung Störungsbehebung Precauciones IndiceIntroducción Paso 2 Conecte el cable de alimentación ConexionesPaso 1 Conecte el monitor al ordenador Selección de la señal de entrada Modos predefinidosModos predefinidos Modos del usuarioFunciones de los controles Conector de entrada de vídeo 1 HD15 Conector ACConector de entrada de vídeo 2 5 BNC Language páginaCambio de la posición de OSD Selección del idioma de OSDFuncionamiento de la indicación en pantalla OSD MenuSelección del modo normal Ajustes modo NormalAjuste del brillo de la imagen Ajuste del contraste de laAjuste del centrado de la Ajustes modo NormalAjuste del tamaño de la Imagen Ajuste de la rotación de la ImagenAjuste de la distorsión de Imagen Cancelación del efecto muaréAjuste de la pantalla ConvergenciaRestauración de los niveles Predefinidos de fábrica Ajuste de la temperatura de ColorPureza de imagen Restauración de todos los datos de ajusteSelección del modo experto Ajustes modo ExpertoAjuste del brillo y contraste De la imagen ¬ BrilloAjuste de la rotación y Distorsión de la imagen Ajuste del color Desmagnetización Para cancelar el bloqueo de los controlesPulse el botón ?//para seleccionar Desblo Aparece la indicación en pantalla PantallaHilos de amortiguación Función Plug & PlayFunción de ahorro de energía Funcionamiento en modo de Ahorro de energíaEspecificaciones Síntoma Compruebe lo siguiente No aparece ninguna imagen Solución de problemasLa imagen aparece CodificadaSolución de problemas Precauzioni IntroduzionePasso 2 Collegare il cavo di alimentazione CollegamentiPasso 1 Collegare il monitor al computer Selezione del segnale d’ingresso Modi predefinitiModi predefiniti Modi definiti dall’utenteFunzioni dei comandi Connettore d’ingresso video 1 HD15 Connettore ACConnettore d’ingresso video 2 5 BNC Language pagAppare l’indicazione a schermo Opzioni Premere il tasto OptionPremere il tasto ¬ ./per selezionare Language Premere il tasto ?//per selezionare la lingua desiderataSelezione del modo normale Regolazioni Modo normaleRegolazione della luminosità Dell’immagine Regolazione del contrasto Dell’immagineRegolazioni Modo normale Regolazione della Dimensione dell’immagineRegolazione della centratura Regolazione della rotazione Dell’immagineRegolazione della distorsione Cuscino dell’immagine Cancellazione dell’effetto moiréRegolazione dello schermo ConvergenzaRipristino dei valori Predefiniti Regolazione della Temperatura di coloreAtterraggio Reimpostazione di tutti i dati della regolazioneRegolazione della luminosità e Del contrasto dell’immagine Regolazioni Modo avanzatoSelezione del modo avanzato Centr Vert Centr OrizzDimens Orizz Dimens VertRegolazione del colore Per annullare il bloccaggio dei comandi SmagnetizzazionePremere il tasto ¬ ./per selezionare Blocc Premere il tasto ?//per selezionare BloccOperazioni di risparmio Energetico Cavi di smorzamentoIl sincronismo H non è presente ’apparecchio entra in modo standbyUso del sistema di orientamento Funzione di avvertimento del segnale d’ingressoCaratteristiche tecniche Visualizza l’impostazione dell’interruttoreGuida alla soluzione dei problemi Guida alla soluzione dei problemi