Pitney Bowes D1500, D1600 manual SwiftStart Operation, Saving a SwiftStart Job

Page 38

3 • Operator Functions

SwiftStart™ Operation

Load material as previously described and select SwiftStart. The machine will feed an envelope and depending on the depth of the envelope, will automatically select the fold type – Single or C fold.

A Trial Piece is automatically produced, enabling you to check the job and to allow the machine to calibrate itself for the material being run.

During this process, if the material in any of the feeders is too heavy, the Double Detect for the relevant feeder(s) will be turned off automatically. This will be indicated by a message on the display.

The machine will ask if the Trial Piece is OK.

If the Trial Piece is OK, select Yes and follow the instructions in the section ‘Saving a SwiftStart™ Job’ below.

If the Trial Piece is NOT OK, select No and follow the on-screen instructions to correct the error. You can adjust the address position, fold panel length and/or the envelope stop position. The envelope stop position will rarely need adjusting - for more information, see page 6-15.

Saving a SwiftStart™ Job

After confirming a Trial Piece is OK, you will be given the option to save the current SwiftStart™ setup as a Job Definition for recall in future. This function requires Supervisor level access (see page 4-2).

If you do NOT save the SwiftStart™ setup, it will only be retained while you are running the current job. If another Job Definition is selected or if power is turned off, the SwiftStart™ settings will be lost.

Automatic Processing

Whether you have chosen to save the SwiftStart™ job or not, you can now commence automatic processing in the normal way:

Press the Start key to commence automatic operation.

The machine will operate until either material runs out or the Stop key is pressed.

3-8

SV40221 Rev. A

Image 38
Contents DI500/DI600 FCC Compliance Canada EMC Compliance Table of Contents Table of Contents Troubleshooting Optical Mark Recognition OMRReference IndexCanada Contacts Pitney Bowes Contact Information ListUSA Contacts SV40221 Rev. a Introduction Important Safety Notes IntroductionTo the Operator Machine Configurations Sheet Feeders Insert Feeders Manual Feeder Sheet Feeders PacPilot Control PanelMeasuring Scale Sealer BottleManual Advance Knob Envelope FeederPacPilot Control Panel Reset CountersCancel Control Panel KeysTrial Piece HomeStart Clear DeckMail Piece Icon Tree Loading InstructionsMail Piece Icon Tree Icons Fold Icons Envelope IconsSeal Icons Insert IconsMail Piece Icon Tree Example Common Terms Mail Piece Material InsertOuter Envelope FanMail Piece Icon Home ScreenJob Definition TreeUsing the Menus Using the Menus Home ScreenReady Menu Structure Select Job p.3-3 SwiftStart p.3-6 Using the Menus Operator Functions Connecting Power About this ChapterRunning a Job Selecting a JobRunning a Trial Piece Automatic Processing Batch CountLoading Material for SwiftStart SwiftStartConstraints and Requirements Loading Sheet FeedersLoading Insert Feeders Loading Envelope FeederSwiftStart Operation Saving a SwiftStart JobLoading Material for Manual Feed Mode Manual FeedManual Feed Operation Manually Feeding Further Sets Setting the Sheet Feeders Operator Functions Setting the Envelope Feeder TIP Setting the Insert Feeders Operator Functions Filling the Envelope Sealer Language Display AdjustmentsMenu Safe SealOperator Functions Supervisor Functions Supervisor Access Code Entering the CodeCreate Job What is it?Where is it? Action…Edit Job Select Edit JobSupervisor Functions Create From Select Create FromDelete Job Select Delete JobManual Feed Option OMR MenuSystem Menu Select System MenuOptical Mark Recognition OMR What is OMR? OMR AvailabilityBM Benchmark SAF SafetyOMR Marks Available BOC Beginning of CollationSFn Select Feed EOC End of CollationSTP Stop TM Timing PAR ParityWAS Wrap Around Sequence IGN IgnorePresent or Absent Continuous Sequence or Page 1 ResetOMR Mark Options Increment or DecrementMarked Piece to be left Unsealed Yes or No Least or Most Significant Mark nearest to BenchmarkAll Sheets, Page 1 Only, Last Page Only Odd or EvenOMR Specifications Leading Edge Creating, Deleting and Viewing OMR Codes Select OMR MenuCreate New OMR Code Tips Delete OMR Code Select Delete OMR Code from the OMR Menu screenView OMR Code Delete this Code View another Code Return to OMR MenuCreating an OMR Job Setting the Type of OMRSetting the OMR Scanning Area Before you StartDefining the first mark position and code length Defining the Clear Zone Measure the OMR mark position OMR Scanner AdjustmentsAligning the Scanners Setting the Top Scanner Position Setting the Bottom Scanner Position Top Scanner Position 10mm Bottom Optical Mark Recognition OMR Troubleshooting Troubleshooting Troubleshooting TipsInsertion Problems General TroubleshootingProblem Remedy Blank ScreenEnvelopes Fail to Open Envelope Sealing ProblemsPoor Envelope Feed Address in wrong position in envelope window Multiple sheets feed when one is expectedPoor Sheet Feed Poor FoldingInserts won’t feed when using Manual Feeder Poor Insert FeedDouble Detect Machine keeps turning Double Detect OFFClearing Material Stalls Manual Advance KnobRemoval & Replacement of the Sheet Feeder Trays a to D Removal & Replacement of the Insert Trays F and GAccess to Internal Areas 1 to Area Access to Area Access to Areas 7Access to the Removeable Paper Path under Insert Feeder F Access to the Top Cover Sheet Feed AreaAccess to the Envelope Exit Area Access to the Envelope Inserting/Sealing AreaEnvelope Stop Position Troubleshooting Reference Specifications Sheet Feeders A, B C and D16, 18 22, 24 28, 30 Paper Weights in lbsFold Type and Overall Thickness Limits Insert Feeders F and G Envelope FeederReference Material Requirements Envelope SealerDrop Stacker Machine Specifications Changing the Envelope Sealer Unit Felts Reference Service Then select System InformationIndex Index Index Index Index Index Index Index Index Index Page SV40221REVA