Minolta Pi3505e LED indicators, Copier has not been turned on, LAN is not connected correctly

Page 19

(3)LED indicators

LED Color

Status

Meaning

 

 

 

 

Lit

The LAN is connected correctly.

 

 

 

 

 

Data is not being sent or received.

Green

Off

The copier has not been turned on.

 

 

The LAN is not connected correctly.

 

 

 

 

Flashing

Data is being sent or received.

 

 

 

Red

Lit

Operating at 100 Mbps

 

 

Off

Operating at 10 Mbps

 

 

 

 

(4)Block Diagram

MFB3 board interface connector 100 pin

Address bus

 

USB

 

controller

 

 

Data bus

 

USB1.1b

 

 

 

 

 

 

 

 

Europe

PCI bus

LAN

 

controller

 

 

USB connector

4 pin

Series B

LAN connector

8 pin

100base-T

Plus trans- former

PCI bus interface for future expansion

Specialized 100 pin connector

C4514S004CA

M-4

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Pi3505e Pi3505e/PS Always observe precautions Safety Precautions for Inspection and ServiceDo not work with wet hands Do not throw toner or the toner bottle into a fireUse the specified parts Be careful with the high-voltage partsMaintain a grounded connection at all times Do not touch a high-temperature partRestore all parts and harnesses to their original positions Precautions for Service JobsPrecautions for the Working Environment Precautions for Servicing with Covers and Parts RemovedPrecautions for storing the toner or imaging cartridge Vorsicht Used Batteries PrecautionsALL Areas GermanyHow to Use this Book Other PrecautionsPrecautions for Service Precautions Before ServiceHandling of Other Parts Precautions for Dis/ReassemblyPrecautions for Circuit Inspection Handling of PWBs During Transportation/StorageHandling of the PC Drum Handling of the Imaging Cartridge and Print Unit Page Contents Page General MECHANICAL/ELECTRICAL Page Controller Specificationss SpecificationsApple Macintosh Computers Pi3505e/PS only Supporting Client SpecificationsIBM PC and Compatible Computers CPUFunctions Function Overview of Circuit BoardsClan circuit board OverviewLAN is not connected correctly LED indicatorsBlock Diagram Copier has not been turned onDIS/REASSEMBLY Adjustment Page Removing parts DISASSEMBLY/REASSEMBLYRemoving the copier covers Remove the reinforcing plate 4 screws Remove the connector bracket 1 screwCN4 Removing the Clan circuit boardCN5 Remove the Clan circuit board Expansion slot 1 CN4 CN3Expansion slot 2 CN5 Removing the expansion hard disk drive CN2 CN1Remove the Compact Flash card Checking the assemblyChecking the operation of the printer controller DISPLAYS/SETTINGS Page Printer controller/Network interface unit Checking Touch Panel DisplaysAssigning the IP Address Controller Network SettingStarting PageScope Light Changing soft switch settings Soft SwitchDisplaying the setting screen from Tech. Rep. Mode Page Specifying Printer Function Soft Switch Settings Soft switch settingsBit Mode Factory Setting 355 Bit HEX20Bit HEX04 Mode Factory SettingBit HEX05 North America Mode Factory Setting 440 Bit HEX12Bit HEX01 Bit HEX80Bit HEX00 Bit 000000 Courier Mode Factory Setting 444 Bit HEX00HEX5C Mode Factory Setting 445 BitHEX3C Mode Factory Setting 449 Bit HEX00Bit HEX30 Bit HEX03 HEXE8HEX8C HEX0FBit HEX23 Page Troubleshooting Page Computer printing problems Problems While Printing from a ComputerNections so that a Printer buffer Switch is not being Used Reduced As overlapping images Drawer, depending on May not be applied Properties dialog boxPrinter’s Properties Ever, depending onApplication, the printing Orientation selected fromCopier to be printed Correctly, refer to Copies is Specified from Copy by usingHas priority differs Copies are not printedOrder to specify booklet Tation, holes cannot be Type and size Overhead projector trans SpecifiedPunched at the top Overhead projector Transparency inter Orientation settings speci Num Symptom Possible Cause Remedy Description Ber CoverSpecify the paper Inter Interleaves or Warm restart operation Warm restart procedureWarm Restart Overview7662-4513-11 Copyright
Top Page Image Contents