Minolta Pi3505e/PS service manual Soft Switch, Changing soft switch settings

Page 34

3.SOFT SWITCH

3-1. Changing soft switch settings

•In order to change the soft switch settings, display the Soft Switch Set screen, and then specify the new setting.

•With scanner- and network-related soft switches, the screen for specifying the settings can be displayed in two ways: from Tech. Rep. Mode or from Maintenance Mode.

(1)Displaying the setting screen from Tech. Rep. Mode

1.Press the [Utility] key to display the Utility screen.

2.Touch [Meter Count].

3.Press the following keys in order to enter Tech. Rep. Mode. Stop → 0 → 0 → Stop → 0 → 1

4.Touch [Soft Switch Settings].

5.In the screen that appears, specify the soft switch settings.

(2)Displaying the setting screen from Maintenance Mode

1.Press the [Utility] key to display the Utility screen.

2.Touch [Meter Count].

3.Press the following keys in order to enter Maintenance Mode. Stop → 0 → 0 → Stop → 0 → 2

4.Touch [Maintenance Mode].

5.Touch [Soft Switch Set].

6.In the screen that appears, specify the soft switch settings.

NOTE

•Since Tech. Rep. Mode and Maintenance Mode should not be available to the user, be sure to turn the copier off, then on again to quit the mode after specifying the necessary settings.

•In order to ensure that the settings have been correctly specified, check the Service Call Report that is outputted.

S-3

Image 34

Contents Pi3505e Pi3505e/PS Safety Precautions for Inspection and Service Always observe precautionsBe careful with the high-voltage parts Do not throw toner or the toner bottle into a fireUse the specified parts Do not work with wet handsPrecautions for Service Jobs Do not touch a high-temperature partRestore all parts and harnesses to their original positions Maintain a grounded connection at all timesPrecautions for the Working Environment Precautions for Servicing with Covers and Parts RemovedPrecautions for storing the toner or imaging cartridge Germany Used Batteries PrecautionsALL Areas VorsichtPrecautions Before Service Other PrecautionsPrecautions for Service How to Use this BookHandling of PWBs During Transportation/Storage Precautions for Dis/ReassemblyPrecautions for Circuit Inspection Handling of Other PartsHandling of the PC Drum Handling of the Imaging Cartridge and Print Unit Page Contents Page General MECHANICAL/ELECTRICAL Page Specifications Controller SpecificationssCPU Supporting Client SpecificationsIBM PC and Compatible Computers Apple Macintosh Computers Pi3505e/PS onlyOverview Function Overview of Circuit BoardsClan circuit board FunctionsCopier has not been turned on LED indicatorsBlock Diagram LAN is not connected correctlyDIS/REASSEMBLY Adjustment Page Removing parts DISASSEMBLY/REASSEMBLYRemoving the copier covers Remove the connector bracket 1 screw Remove the reinforcing plate 4 screwsCN4 Removing the Clan circuit boardCN5 Remove the Clan circuit board Expansion slot 1 CN4 CN3Expansion slot 2 CN5 Removing the expansion hard disk drive CN1 CN2Remove the Compact Flash card Checking the assemblyChecking the operation of the printer controller DISPLAYS/SETTINGS Page Checking Touch Panel Displays Printer controller/Network interface unitAssigning the IP Address Controller Network SettingStarting PageScope Light Changing soft switch settings Soft SwitchDisplaying the setting screen from Tech. Rep. Mode Page Soft switch settings Specifying Printer Function Soft Switch SettingsMode Factory Setting 355 Bit HEX20 BitBit HEX04 Mode Factory SettingBit HEX05 Mode Factory Setting 440 Bit HEX12 North AmericaBit HEX01 Bit HEX80Bit HEX00 Mode Factory Setting 444 Bit HEX00 Bit 000000 CourierMode Factory Setting 445 Bit HEX5CHEX3C Mode Factory Setting 449 Bit HEX00Bit HEX30 HEXE8 Bit HEX03HEX0F HEX8CBit HEX23 Page Troubleshooting Page Computer printing problems Problems While Printing from a ComputerNections so that a Printer buffer Switch is not being Used Reduced As overlapping images Drawer, depending on Properties dialog box May not be appliedOrientation selected from Ever, depending onApplication, the printing Printer’s PropertiesCopier to be printed Copies are not printed Copies is Specified from Copy by usingHas priority differs Correctly, refer toOrder to specify booklet Tation, holes cannot be Type and size Overhead projector trans SpecifiedPunched at the top Overhead projector Transparency inter Orientation settings speci Num Symptom Possible Cause Remedy Description Ber CoverSpecify the paper Inter Interleaves or Overview Warm restart procedureWarm Restart Warm restart operationCopyright 7662-4513-11