Minolta Pi3505e/PS service manual CN1, CN2

Page 28

4599U022AA

4599U038AB

6. Remove the mechanical circuit board cover from the hard disk drive (4 screws).

✽When attaching the hard disk drive to the mechan- ical circuit board, tighten the bushing at the back of the mechanical circuit board until it appears as shown in the illustration.

(5)Removing the power supply circuit board for the expansion hard disk drive

	4348U018AC
CN1	4599U013AB
CN2	4599U018AA

1. Remove the lower rear cover (4 screws).

NOTE

During assembly, place a toothed washer onto the screw in the upper-right corner of the lower rear cover.

2.Disconnect the connectors from CN1 and CN2 on the power supply circuit board.

D-7

Image 28

Contents Pi3505e Pi3505e/PS Safety Precautions for Inspection and Service Always observe precautionsDo not throw toner or the toner bottle into a fire Use the specified partsBe careful with the high-voltage parts Do not work with wet handsDo not touch a high-temperature part Restore all parts and harnesses to their original positionsPrecautions for Service Jobs Maintain a grounded connection at all timesPrecautions for the Working Environment Precautions for Servicing with Covers and Parts RemovedPrecautions for storing the toner or imaging cartridge Used Batteries Precautions ALL AreasGermany VorsichtOther Precautions Precautions for ServicePrecautions Before Service How to Use this BookPrecautions for Dis/Reassembly Precautions for Circuit InspectionHandling of PWBs During Transportation/Storage Handling of Other PartsHandling of the PC Drum Handling of the Imaging Cartridge and Print Unit Page Contents Page General MECHANICAL/ELECTRICAL Page Specifications Controller SpecificationssSupporting Client Specifications IBM PC and Compatible ComputersCPU Apple Macintosh Computers Pi3505e/PS onlyFunction Overview of Circuit Boards Clan circuit boardOverview FunctionsLED indicators Block DiagramCopier has not been turned on LAN is not connected correctlyDIS/REASSEMBLY Adjustment Page Removing parts DISASSEMBLY/REASSEMBLYRemoving the copier covers Remove the connector bracket 1 screw Remove the reinforcing plate 4 screwsCN4 Removing the Clan circuit boardCN5 Remove the Clan circuit board Expansion slot 1 CN4 CN3Expansion slot 2 CN5 Removing the expansion hard disk drive CN1 CN2Remove the Compact Flash card Checking the assemblyChecking the operation of the printer controller DISPLAYS/SETTINGS Page Checking Touch Panel Displays Printer controller/Network interface unitAssigning the IP Address Controller Network SettingStarting PageScope Light Changing soft switch settings Soft SwitchDisplaying the setting screen from Tech. Rep. Mode Page Soft switch settings Specifying Printer Function Soft Switch SettingsMode Factory Setting 355 Bit HEX20 BitBit HEX04 Mode Factory SettingBit HEX05 Mode Factory Setting 440 Bit HEX12 North AmericaBit HEX01 Bit HEX80Bit HEX00 Mode Factory Setting 444 Bit HEX00 Bit 000000 CourierMode Factory Setting 445 Bit HEX5CHEX3C Mode Factory Setting 449 Bit HEX00Bit HEX30 HEXE8 Bit HEX03HEX0F HEX8CBit HEX23 Page Troubleshooting Page Computer printing problems Problems While Printing from a ComputerNections so that a Printer buffer Switch is not being Used Reduced As overlapping images Drawer, depending on Properties dialog box May not be appliedEver, depending on Application, the printingOrientation selected from Printer’s PropertiesCopier to be printed Copies is Specified from Copy by using Has priority differsCopies are not printed Correctly, refer toOrder to specify booklet Tation, holes cannot be Type and size Overhead projector trans SpecifiedPunched at the top Overhead projector Transparency inter Orientation settings speci Num Symptom Possible Cause Remedy Description Ber CoverSpecify the paper Inter Interleaves or Warm restart procedure Warm RestartOverview Warm restart operationCopyright 7662-4513-11