Minolta Pi3505e/PS service manual Mode Factory Setting, Bit HEX04, Bit HEX05

Page 38

Mode

Factory Setting

413

7

6

5

4

3

2

1

0

Bit:

0

0

0

0

0

1

0

0

HEX:04

Bit

Feature

Logical Value

Description

0

1

7 – 6

Selection of fax (G3-1) output tray✽

Bit 7-6:

00

1st paper output

Specifies the tray that fax

tray

(G3-1) prints are fed into

01

2nd paper output

when a finisher is installed.

The 3rd paper output tray is

tray

available only if the additional

10

Additional bin

bin kit is installed.

11

Do not specify this

setting.

5 – 4

Selection of output tray for com-

Bit 5-4:

00

1st paper output

Specifies the tray that com-

puter printouts

✽

tray

puter printouts are fed into

01

Sorted copy tray

when a finisher is installed.

The 3rd paper output tray is

10

3rd paper output

available only if the additional

tray

bin kit is installed.

11

Do not specify this

setting.

3

Fixed

Do not change this setting.

2

Selection of copy output bin

✽

Bin 1

Bin 2

Specifies the copy output bin when the job sepa-

rator is installed.

1

Selection of fax (G3-1) output bin

Bin 1

Bin 2

Specifies the bin that fax (G3-1) prints are fed into

✽

when the job separator is installed.

0

Selection of output bin for computer

Bin 1

Bin 2

Specifies the bin that computer printouts are fed

printouts

✽

into when the job separator is installed.

Mode

Factory Setting

432

7

6

5

4

3

2

1

0

Bit:

0

0

0

0

0

1

0

1

HEX:05

Bit

Feature

Logical Value

Description

0

1

7 – 0

Wait time for computer printing with

Bit 7-0:

Specifies the wait time for

full memory (M)

✽

computer printing when the

00000000

Erase immediately

memory is full (M)

00000001

1 minute

Setting range: 0 minutes, 1 to

30 minutes

(1-minute intervals)

00000101

5 minutes

Erases the computer print

job after reaching the speci-

00011110

30 minutes

fied wait time when the mem-

Others

Do not specify

ory is full.

these settings.

Setting conditions for bits 7

through 4 of mode 320,

around-the-clock monitoring

timer (t1), and bits 3 through

0 of mode 320, around-the-

clock monitoring timer (t2):

Each must be set so that

t2

t1

M.

Note: Features marked with asterisks can be specified by the user. ✽ indicates screen settings.

S-7

Image 38

Contents Pi3505e Pi3505e/PS Safety Precautions for Inspection and Service Always observe precautionsBe careful with the high-voltage parts Do not throw toner or the toner bottle into a fireUse the specified parts Do not work with wet handsPrecautions for Service Jobs Do not touch a high-temperature partRestore all parts and harnesses to their original positions Maintain a grounded connection at all timesPrecautions for storing the toner or imaging cartridge Precautions for Servicing with Covers and Parts RemovedPrecautions for the Working Environment Germany Used Batteries PrecautionsALL Areas VorsichtPrecautions Before Service Other PrecautionsPrecautions for Service How to Use this BookHandling of PWBs During Transportation/Storage Precautions for Dis/ReassemblyPrecautions for Circuit Inspection Handling of Other PartsHandling of the PC Drum Handling of the Imaging Cartridge and Print Unit Page Contents Page General MECHANICAL/ELECTRICAL Page Specifications Controller SpecificationssCPU Supporting Client SpecificationsIBM PC and Compatible Computers Apple Macintosh Computers Pi3505e/PS onlyOverview Function Overview of Circuit BoardsClan circuit board FunctionsCopier has not been turned on LED indicatorsBlock Diagram LAN is not connected correctlyDIS/REASSEMBLY Adjustment Page Removing the copier covers DISASSEMBLY/REASSEMBLYRemoving parts Remove the connector bracket 1 screw Remove the reinforcing plate 4 screwsCN5 Removing the Clan circuit boardCN4 Remove the Clan circuit board Expansion slot 2 CN5 CN3Expansion slot 1 CN4 Removing the expansion hard disk drive CN1 CN2Checking the operation of the printer controller Checking the assemblyRemove the Compact Flash card DISPLAYS/SETTINGS Page Checking Touch Panel Displays Printer controller/Network interface unitStarting PageScope Light Controller Network SettingAssigning the IP Address Displaying the setting screen from Tech. Rep. Mode Soft SwitchChanging soft switch settings Page Soft switch settings Specifying Printer Function Soft Switch SettingsMode Factory Setting 355 Bit HEX20 BitBit HEX05 Mode Factory SettingBit HEX04 Mode Factory Setting 440 Bit HEX12 North AmericaBit HEX00 Bit HEX80Bit HEX01 Mode Factory Setting 444 Bit HEX00 Bit 000000 CourierMode Factory Setting 445 Bit HEX5CBit HEX30 Mode Factory Setting 449 Bit HEX00HEX3C HEXE8 Bit HEX03HEX0F HEX8CBit HEX23 Page Troubleshooting Page Nections so that a Printer buffer Switch is not being Used Problems While Printing from a ComputerComputer printing problems Reduced As overlapping images Drawer, depending on Properties dialog box May not be appliedOrientation selected from Ever, depending onApplication, the printing Printer’s PropertiesCopier to be printed Copies are not printed Copies is Specified from Copy by usingHas priority differs Correctly, refer toOrder to specify booklet Punched at the top Type and size Overhead projector trans SpecifiedTation, holes cannot be Overhead projector Transparency inter Specify the paper Inter Interleaves or Num Symptom Possible Cause Remedy Description Ber CoverOrientation settings speci Overview Warm restart procedureWarm Restart Warm restart operationCopyright 7662-4513-11