Minolta Pi3505e/PS Safety Precautions for Inspection and Service, Always observe precautions

Page 2

1.SAFETY PRECAUTIONS FOR INSPECTION AND SERVICE

•When performing inspection and service procedures, observe the following precautions to prevent accidents and ensure utmost safety.

✽Depending on the model, some of the precautions given in the following do not apply.

• Different markings are used to denote specific meanings as detailed below.

WARNING

•Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

•Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

•The following graphic symbols are used to give instructions that need to be observed.

Used to call the service technician attention to what is graphically represented inside the marking (including a warning).

Used to prohibit the service technician from doing what is graphically represented inside the marking.

Used to instruct the service technician to do what is graphically represented inside the marking.

1-1. Warning

WARNING

1.Always observe precautions.

•Parts requiring special attention in this product will include a label containing the mark shown on the left plus precautionary notes. Be sure to observe the precautions.

•Be sure to observe the “Safety Information” given in the Operator’s Manual.

P-1

Image 2

Contents Pi3505e Pi3505e/PS Safety Precautions for Inspection and Service Always observe precautionsBe careful with the high-voltage parts Do not throw toner or the toner bottle into a fireUse the specified parts Do not work with wet handsPrecautions for Service Jobs Do not touch a high-temperature partRestore all parts and harnesses to their original positions Maintain a grounded connection at all timesPrecautions for storing the toner or imaging cartridge Precautions for Servicing with Covers and Parts RemovedPrecautions for the Working Environment Germany Used Batteries PrecautionsALL Areas VorsichtPrecautions Before Service Other PrecautionsPrecautions for Service How to Use this BookHandling of PWBs During Transportation/Storage Precautions for Dis/ReassemblyPrecautions for Circuit Inspection Handling of Other PartsHandling of the PC Drum Handling of the Imaging Cartridge and Print Unit Page Contents Page General MECHANICAL/ELECTRICAL Page Specifications Controller SpecificationssCPU Supporting Client SpecificationsIBM PC and Compatible Computers Apple Macintosh Computers Pi3505e/PS onlyOverview Function Overview of Circuit BoardsClan circuit board FunctionsCopier has not been turned on LED indicatorsBlock Diagram LAN is not connected correctlyDIS/REASSEMBLY Adjustment Page Removing the copier covers DISASSEMBLY/REASSEMBLYRemoving parts Remove the connector bracket 1 screw Remove the reinforcing plate 4 screwsCN5 Removing the Clan circuit boardCN4 Remove the Clan circuit board Expansion slot 2 CN5 CN3Expansion slot 1 CN4 Removing the expansion hard disk drive CN1 CN2Checking the operation of the printer controller Checking the assemblyRemove the Compact Flash card DISPLAYS/SETTINGS Page Checking Touch Panel Displays Printer controller/Network interface unitStarting PageScope Light Controller Network SettingAssigning the IP Address Displaying the setting screen from Tech. Rep. Mode Soft SwitchChanging soft switch settings Page Soft switch settings Specifying Printer Function Soft Switch SettingsMode Factory Setting 355 Bit HEX20 BitBit HEX05 Mode Factory SettingBit HEX04 Mode Factory Setting 440 Bit HEX12 North AmericaBit HEX00 Bit HEX80Bit HEX01 Mode Factory Setting 444 Bit HEX00 Bit 000000 CourierMode Factory Setting 445 Bit HEX5CBit HEX30 Mode Factory Setting 449 Bit HEX00HEX3C HEXE8 Bit HEX03HEX0F HEX8CBit HEX23 Page Troubleshooting Page Nections so that a Printer buffer Switch is not being Used Problems While Printing from a ComputerComputer printing problems Reduced As overlapping images Drawer, depending on Properties dialog box May not be appliedOrientation selected from Ever, depending onApplication, the printing Printer’s PropertiesCopier to be printed Copies are not printed Copies is Specified from Copy by usingHas priority differs Correctly, refer toOrder to specify booklet Punched at the top Type and size Overhead projector trans SpecifiedTation, holes cannot be Overhead projector Transparency inter Specify the paper Inter Interleaves or Num Symptom Possible Cause Remedy Description Ber CoverOrientation settings speci Overview Warm restart procedureWarm Restart Warm restart operationCopyright 7662-4513-11