Minolta Pi3505e Remove the reinforcing plate 4 screws, Remove the connector bracket 1 screw

Page 23

4599U009AB

4599U040AA

4599U036AA

4514U003AA

5.Remove the back panel (13 screws). (To remove the panel, slightly lift it up.)

NOTE

When attaching the rear cover, use 6 gold-colored screws at the top.

6. Remove the reinforcing plate (4 screws).

NOTE

Make sure that the flat cable for the hard disk drive and the power relay harness are not pinched.

7. Remove the connector bracket (1 screw).

D-2

Image 23

Contents Pi3505e Pi3505e/PS Always observe precautions Safety Precautions for Inspection and ServiceDo not work with wet hands Do not throw toner or the toner bottle into a fireUse the specified parts Be careful with the high-voltage partsMaintain a grounded connection at all times Do not touch a high-temperature partRestore all parts and harnesses to their original positions Precautions for Service JobsPrecautions for storing the toner or imaging cartridge Precautions for Servicing with Covers and Parts RemovedPrecautions for the Working Environment Vorsicht Used Batteries PrecautionsALL Areas GermanyHow to Use this Book Other PrecautionsPrecautions for Service Precautions Before ServiceHandling of Other Parts Precautions for Dis/ReassemblyPrecautions for Circuit Inspection Handling of PWBs During Transportation/StorageHandling of the PC Drum Handling of the Imaging Cartridge and Print Unit Page Contents Page General MECHANICAL/ELECTRICAL Page Controller Specificationss SpecificationsApple Macintosh Computers Pi3505e/PS only Supporting Client SpecificationsIBM PC and Compatible Computers CPUFunctions Function Overview of Circuit BoardsClan circuit board OverviewLAN is not connected correctly LED indicatorsBlock Diagram Copier has not been turned onDIS/REASSEMBLY Adjustment Page Removing the copier covers DISASSEMBLY/REASSEMBLYRemoving parts Remove the reinforcing plate 4 screws Remove the connector bracket 1 screwCN5 Removing the Clan circuit boardCN4 Remove the Clan circuit board Expansion slot 2 CN5 CN3Expansion slot 1 CN4 Removing the expansion hard disk drive CN2 CN1Checking the operation of the printer controller Checking the assemblyRemove the Compact Flash card DISPLAYS/SETTINGS Page Printer controller/Network interface unit Checking Touch Panel DisplaysStarting PageScope Light Controller Network SettingAssigning the IP Address Displaying the setting screen from Tech. Rep. Mode Soft SwitchChanging soft switch settings Page Specifying Printer Function Soft Switch Settings Soft switch settingsBit Mode Factory Setting 355 Bit HEX20Bit HEX05 Mode Factory SettingBit HEX04 North America Mode Factory Setting 440 Bit HEX12Bit HEX00 Bit HEX80Bit HEX01 Bit 000000 Courier Mode Factory Setting 444 Bit HEX00HEX5C Mode Factory Setting 445 BitBit HEX30 Mode Factory Setting 449 Bit HEX00HEX3C Bit HEX03 HEXE8HEX8C HEX0FBit HEX23 Page Troubleshooting Page Nections so that a Printer buffer Switch is not being Used Problems While Printing from a ComputerComputer printing problems Reduced As overlapping images Drawer, depending on May not be applied Properties dialog boxPrinter’s Properties Ever, depending onApplication, the printing Orientation selected fromCopier to be printed Correctly, refer to Copies is Specified from Copy by usingHas priority differs Copies are not printedOrder to specify booklet Punched at the top Type and size Overhead projector trans SpecifiedTation, holes cannot be Overhead projector Transparency inter Specify the paper Inter Interleaves or Num Symptom Possible Cause Remedy Description Ber CoverOrientation settings speci Warm restart operation Warm restart procedureWarm Restart Overview7662-4513-11 Copyright