Ultra electronic Prima 3 user manual Wind the ribbon, taking up the slack, Close the printer door

Page 15

(to the next page)

5. Wind the ribbon, taking up the slack.

Turn the knob in the arrow direction to wind a small portion of the ink ribbon. If the ink ribbon does not wind up, go back to step 3, and insert the ink ribbon firmly into the bobbin holders.

7. Close the printer door.

If you want to mount the retransfer film, keep the door open and go to the next page.

CAUTION If the ink ribbon is not tightly wound, the slack may cause the ribbon to be caught in the parts

of the printer when you set the cassette, or the card to be printed in uneven colors.

6. Insert the cassette along the guide rail.

Insert the cassette until it clicks securely into position. The lever returns to its original position.

Guide rail

CAUTION

• The cassette containing the ink

ribbon is heavy. Hold the cassette with both hands when you set or take out the cassette.

If the cassette unit is not inserted until it clicks securely into position before printing, horizontal lines may be printed with the image.

Memo

When the ink ribbon is wound up to the end,

I n k R u n O u t

appears on the LCD panel.

After replacement press the RESET button, then press the ENTER button.

If the ink ribbon is not set properly,

I n k S e a r c h

or

I n k B r o k e n

appears on the LCD panel. When these messages are output, check:

The ink ribbon is firmly inserted into the bobbin holders.

The ink face of the ribbon is directed correctly.

The feeding and winding bobbins are mounted correctly.

Memo

To mount the ink ribbon which is partially used, set the unused portion of the ribbon (yellow bobbin) on the bobbin holder indicated with an arrow on the seal of the cassette.

Printing with the ink ribbon set improperly may cause the image to be faint.

15

Image 15
Contents Prima Harmonized Standards 89/336/EEC2006/95/EC Relating to electromagnetic compatibilityOperation is subject to the following two conditions Information for USAContents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructedDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it outHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useEscape Clause Installation 35% to 70%To 86 F Front Slide knob AccessoryPower input jack Names of partsPlease ask your dealer for the Compact IC unit connection Connecting the IC unit Sold separatelyConnecting the Laminator Set-upCheck the plug For AC 120V type Connecting the power cordInstall the unit connecting cable.optional Pin Connecting cablePortion B See the description in Jam Transfer on p.50 Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximatelySetting the ink ribbon Insert the cassette along the guide rail When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Close the printer doorRemove the retransfer film cassette Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyIf the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteShown in the illustration Setting cardsThis 300 pieces is not a guaranteed quantity Cassette and/or the ink ribbon cassetteDealer For a magnetic or IC card, encoding error may happen When moving the card bracketConsult your dealer to purchase new gloves See p.34 in this manual Printing on cards with magnetic strips is not guaranteedFor JIS II cards For ISO cardsConnect the printer and host computer with the USB cable Connecting with a host computerConnecting with USB cable Connecting with Ethernet cableConnecting Multiple Printers When connecting a host computer to multiple printersCopyright of the Software is displayed Names of parts on the operation panel BeforeuseLCD operation display content Operation display LED contents LCD panelOperation display LED Ready LED will light up Turning on the powerTurn the power on Represents on and O represents OFF OperationTurning off the power About the Reset buttonIs loaded User mode screen flow User modesPress Submenu Main menu Submenu To the nextDisplay mode settings Exit user Reset the free counterPress to reset Clearing the free counterSpecial ink SP-Ink 2 level Ink mode settingUV ink level setting Set the K printing mode2Retransfer mode setting Exit user mode Set the buzzer Buzzer mode settingTo select the setting value and press Setting the bend remedy modeSet the bend remedy roller temperature Bend remedy speed settingsUnit No. Setting Card Thickness setting mode IC contact setting modeCoercivity setting mode Non-contact IC antenna setting modeNetwork setting Input method Address Setting mode Low temperature stand-by mode setting Download mode settingSet position of MAC address print Close the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unitWipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.14, 16 in this manualSee p.31 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown belowCleaning the magnetic head Set a cleaning cardConfirm that the retransfer film cassette has been removed Cleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Layout of rollers inside the printer TroubleshootingCleaning unit All rollers require routine cleaningTo initialize the unit Error code listingMG mechanical error Hardware errorError MG connection errorMending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not completeHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Main specifications Specifications34.3 38.1 External appearance and dimensionsCase of disposal Front viewUltra Electronics Card Systems