Ultra electronic Prima 3 user manual Cassette and/or the ink ribbon cassette, Setting cards

Page 18

Set-up(continued)

Caution when loading the retransfer film

cassette and/or the ink ribbon cassette

The following caution shall be kept when the retransfer

film cassette and/or the ink ribbon cassette is removed

because of card jam or other trouble.

Please pay enough attention so that the retransfer film and/or ink ribbon is maintained at the right position. Particularly, the ink ribbon is extremely thin, therefore it apt to slip down when the cassette is removed as

shown in the illustration.

Improper Winding

Setting cards

Please use cards specified by your dealer. This unit can take both 0.76 mm(0.03inches)-thick and 0.25 mm (0.01inches)-thick cards. The factory setting is for 0.76 mm-thickness.

CAUTION

Fingerprints, soiling, etc. on card surface can result in print errors. Wear lint-free gloves when handling.

Inserting cards

Adjust the position with hands so that the media position of take-up side and supply side becomes parallel

When loaded in this condition, it may cause improper printing such as INK RUNOUT error, improper color printing etc.

To avoid this, please handle the ink ribbon and/or the retransfer film very carefully with hands so that the media position of take-up side become parallel.

Please do not touch the print side of the ink ribbon and/ or the retransfer film with your hands. Otherwise, it may cause improper printing.

When adjusting the print position of the retransfer film and/or ink ribbon, please follow the instruction label attached on the cassettes.

The unit can take about 300 0.76mm-thick cards.

As for 0.25mm thick cards do not insert more than 300 pieces.

This 300 pieces is not a guaranteed quantity.

In the event of card feed failure, caused by card bending or others reduce card quantity.

CAUTION

When removing new cards from the box, it is possible that cards may be stuck due to static electricity. In this case, peel the cards off one at a time before setting into position. Hold the edges of the card when carrying out these operations.

1.Open the card tray.

Hold the lower part of the card tray and pull the tray toward you slowly until it no longer moves.

18

Image 18
Contents Prima Relating to electromagnetic compatibility 89/336/EEC2006/95/EC Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause Installation 35% to 70%To 86 F Names of parts AccessoryPower input jack Front Slide knobSet-up Connecting the IC unit Sold separatelyConnecting the Laminator Please ask your dealer for the Compact IC unit connectionPin Connecting cable Connecting the power cordInstall the unit connecting cable.optional Check the plug For AC 120V typeCard stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle Portion B See the description in Jam Transfer on p.50Setting the ink ribbon Close the printer door When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmInsert the retransfer film into the cassette Remove the retransfer film cassetteOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsThis 300 pieces is not a guaranteed quantity Shown in the illustrationDealer For a magnetic or IC card, encoding error may happen When moving the card bracketConsult your dealer to purchase new gloves For ISO cards Printing on cards with magnetic strips is not guaranteedFor JIS II cards See p.34 in this manualConnecting with Ethernet cable Connecting with a host computerConnecting with USB cable Connect the printer and host computer with the USB cableConnecting Multiple Printers When connecting a host computer to multiple printersCopyright of the Software is displayed Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentOperation Turning on the powerTurn the power on Represents on and O represents OFF Operation display LED Ready LED will light upTurning off the power About the Reset buttonIs loaded User mode screen flow User modesPress Submenu To the next Main menu SubmenuDisplay mode settings Clearing the free counter Reset the free counterPress to reset Exit userSet the K printing mode2 Ink mode settingUV ink level setting Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerBend remedy speed settings Setting the bend remedy modeSet the bend remedy roller temperature To select the setting value and pressNon-contact IC antenna setting mode Card Thickness setting mode IC contact setting modeCoercivity setting mode Unit No. SettingNetwork setting Input method Address Setting mode Low temperature stand-by mode setting Download mode settingSet position of MAC address print Open the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.14, 16 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.31 in this manualCleaning the magnetic head Set a cleaning cardConfirm that the retransfer film cassette has been removed Cleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance All rollers require routine cleaning TroubleshootingCleaning unit Layout of rollers inside the printerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsFront view External appearance and dimensionsCase of disposal 34.3 38.1Ultra Electronics Card Systems