Ultra electronic Prima 3 Connecting Multiple Printers, Copyright of the Software is displayed

Page 22

Set-up(continued)

Connecting Multiple Printers

When connecting a host computer to multiple printers,

set different Unit Numbers from 1 to 7 for each printer. Refer to see the page 36 of the instruction manual.

To connect multiple printers to a network, you must configure the IP addresses for a every printer, For details, see page 37 of this documentation.

The Copyright of the Software is displayed

This product includes software developed by the Open SSL

Project for use in the Open SSL Toolkit . (http:// www.openssl.org/)

This product includes cryptographic software written by Eric

Young(eay@cryptsoft.com).

T h i s p r o d u c t i n c l u d e s s o f t w a r e w r i t t e n b y Ti m Hudson(tjh@cryptsoft.com).

Image 22

Contents Prima Relating to electromagnetic compatibility 89/336/EEC2006/95/EC Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause 35% to 70% InstallationTo 86 F Names of parts AccessoryPower input jack Front Slide knobSet-up Connecting the IC unit Sold separatelyConnecting the Laminator Please ask your dealer for the Compact IC unit connectionPin Connecting cable Connecting the power cordInstall the unit connecting cable.optional Check the plug For AC 120V typeCard stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle Portion B See the description in Jam Transfer on p.50Setting the ink ribbon Close the printer door When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmInsert the retransfer film into the cassette Remove the retransfer film cassetteOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsThis 300 pieces is not a guaranteed quantity Shown in the illustrationWhen moving the card bracket Dealer For a magnetic or IC card, encoding error may happenConsult your dealer to purchase new gloves For ISO cards Printing on cards with magnetic strips is not guaranteedFor JIS II cards See p.34 in this manualConnecting with Ethernet cable Connecting with a host computerConnecting with USB cable Connect the printer and host computer with the USB cableWhen connecting a host computer to multiple printers Connecting Multiple PrintersCopyright of the Software is displayed Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentOperation Turning on the powerTurn the power on Represents on and O represents OFF Operation display LED Ready LED will light upAbout the Reset button Turning off the powerIs loaded User modes User mode screen flowPress Submenu To the next Main menu SubmenuDisplay mode settings Clearing the free counter Reset the free counterPress to reset Exit userSet the K printing mode2 Ink mode settingUV ink level setting Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerBend remedy speed settings Setting the bend remedy modeSet the bend remedy roller temperature To select the setting value and pressNon-contact IC antenna setting mode Card Thickness setting mode IC contact setting modeCoercivity setting mode Unit No. SettingNetwork setting Input method Address Setting mode Download mode setting Low temperature stand-by mode settingSet position of MAC address print Open the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.14, 16 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.31 in this manualSet a cleaning card Cleaning the magnetic headConfirm that the retransfer film cassette has been removed Once printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance All rollers require routine cleaning TroubleshootingCleaning unit Layout of rollers inside the printerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsFront view External appearance and dimensionsCase of disposal 34.3 38.1Ultra Electronics Card Systems