Ultra electronic Prima 3 user manual Installation, 35% to 70%, To 86 F

Page 9

Installation

The performance of the card printer is strongly influenced by the installation location.Be careful of the following items as for installation location.

•Install in the locations is not so much as to cause print defect due to dust adherence.

Dusty environment increases print defect. It is recommended that the card printer is used in the locations with the cleanness Class 8 or better of ISO14661-1. But at least avoid the following locations.

(1)Carpeted room

(2)Crowded locations

(3)Locations where paper(corrugated etc.) is handled

(4)Areas near copy machines

When the card printer is not used, it is recommended that the power is turned off and the printer is covered by plastic sheet etc.(not textile).

•Install in the locations where the printer performance is kept.

Avoid the locations below where the performance or life of the printer is affected.

(1)Locations where there is vibrations or shock

(2)Locations exposed to direct sunshine.

(3)Wet locations without ventilation

(4)Unstable locations and sloped surface

(5)Areas near air conditioners, humidifiers, stoves, etc. that may cause condensation within the printer .

•Install in the environment that gives full play to the printer ability.

The printer is to be installed in an environment

with the following temperature and humidity.
Temperature	:	15	° C to 30 ° C
			59° F to 86 ° F
Humidity	:	35% to 70%

CAUTION

Use of the printer in an environment with temperature lower than the above range may cause

retransfer errors and use of the printer in an environment with temperature higher than the above range may cause print errors from deformation of the cards and wrinkling of the film.

Installation diagram

Ventilation holes are provided for the cooling fan on the bottom and sides of the unit. Avoid inserting any object into the gap between the bottom of the unit and the top

of the stand. Install the unit with its sides at least 20cm away from the surrounding wall as illustrated in the diagram, and keep the back of the unit at least 10cm away from the wall. Also, do not place any object on top of the unit.

	Do not place objects on top
20cm or more	20cm or more
7.9 inches or more	7.9 inches or more

9

Image 9

Contents Prima 2006/95/EC 89/336/EECRelating to electromagnetic compatibility Harmonized StandardsOperation is subject to the following two conditions Information for USAContents Manual any time as you need Do not touch the power plug during electrical stormsDo not use a line voltage other than instructed Do not wet the machine with waterPull out the power plug before cleaning the machine Do not use the machine while it has a faultHold the body of the power plug when pulling it out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation 35% to 70%To 86 F Power input jack AccessoryNames of parts Front Slide knobConnecting the Laminator Connecting the IC unit Sold separatelySet-up Please ask your dealer for the Compact IC unit connectionInstall the unit connecting cable.optional Connecting the power cordPin Connecting cable Check the plug For AC 120V typeHang the stacker claw on the stacker receptacle Installing the card stackerCard stacker is capable of containing approximately Portion B See the description in Jam Transfer on p.50Setting the ink ribbon Wind the ribbon, taking up the slack When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide railInsert the retransfer film into the cassette Setting the retransfer filmOtherwise the printer may fail Slowly Remove the retransfer film cassetteWind the retransfer film to take up the slack When the retransfer film is wound up to the endOpen the printer door and insert the cassette If the retransfer film is not set properlyThis 300 pieces is not a guaranteed quantity Setting cardsCassette and/or the ink ribbon cassette Shown in the illustrationDealer For a magnetic or IC card, encoding error may happen When moving the card bracketConsult your dealer to purchase new gloves For JIS II cards Printing on cards with magnetic strips is not guaranteedFor ISO cards See p.34 in this manualConnecting with USB cable Connecting with a host computerConnecting with Ethernet cable Connect the printer and host computer with the USB cableConnecting Multiple Printers When connecting a host computer to multiple printersCopyright of the Software is displayed Names of parts on the operation panel BeforeuseLCD operation display content Operation display LED contents LCD panelTurn the power on Represents on and O represents OFF Turning on the powerOperation Operation display LED Ready LED will light upTurning off the power About the Reset buttonIs loaded User mode screen flow User modesPress Submenu Main menu Submenu To the nextDisplay mode settings Press to reset Reset the free counterClearing the free counter Exit userUV ink level setting Ink mode settingSet the K printing mode2 Special ink SP-Ink 2 levelRetransfer mode setting Exit user mode Set the buzzer Buzzer mode settingSet the bend remedy roller temperature Setting the bend remedy modeBend remedy speed settings To select the setting value and pressCoercivity setting mode Card Thickness setting mode IC contact setting modeNon-contact IC antenna setting mode Unit No. SettingNetwork setting Input method Address Setting mode Low temperature stand-by mode setting Download mode settingSet position of MAC address print Cleaning the cleaning rollers CareandcleaningOpen the card tray Remove the cleaning unit Close the card trayCleaning the fan filter Cleaning the thermal headSee p.14, 16 in this manual Wipe the head indicated withInstall the fan filters back to the original positions Cleaning the card feed rollers and heat RollersIf the sponge is removed, attach it again as shown below See p.31 in this manualCleaning the magnetic head Set a cleaning cardConfirm that the retransfer film cassette has been removed Cleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Cleaning unit TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printerTo initialize the unit Error code listingError Hardware errorMG connection error MG mechanical errorAbout printing errors Stopping when printingWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Main specifications SpecificationsCase of disposal External appearance and dimensionsFront view 34.3 38.1Ultra Electronics Card Systems