Ultra electronic Prima 3 user manual Buzzer mode setting, Exit user mode Set the buzzer

Ad

Page 34

Operation (continued)

Buzzer mode setting

Power saving mode settings

The buzzer indicating errors can be turned on or off.

> B u z z e r

EXIT

Exit user mode

O n

Set the buzzer:

there are two settings

(On, off)

			ENTER
Press			to select the setting and press	to save.
	(The electronic beep sounds.The beep will not sound

if the buzzer mode setting is set to off.)

When Off is specified,

•electronic beep sound indicating an error,

•electronic beep sound indicating the number of cards, and

•electronic beep sound indicating settings saved with the ENTER button in the user mode are muted.

The printer enters into the power save mode after a specified period of time if none of operation buttons are touched in the Ready state. The heat roller for retransfer, bend remedial roller, and back-light of the LCD panel are turned off in the power save mode.

> P o w e r S a v i n g

EXIT

Exit user mode

o f f

Power saving settings:

there are 9 options.

				ENTER
Press				to select the setting and press	to save.
	(The electronic beep sounds.The beep will not sound

if the buzzer mode setting is set to off.)

Press the EXIT button to cancel the user mode, and the printer starts.

Off:

Not in power saving mode.

Setting options: [5,10,15,20,25,30,45,60] (units: minutes)

If printing is not to be carried out for a period longer than the

set time, switch the units heater off. (Power save status)

“Sleeping” appears on the LCD panel in the power save mode. The operation buttons are disabled in this mode.

See step 2 in “Canceling the power save mode” to enable the operation buttons.

S l e e p i n g

The printer moves to the power save mode when the specified time arrives even if you turns off the printer and turn it on again.

Canceling the power save mode 1. From the host computer

Enter a control command to print the card. The power save mode is cancelled, and printing automatically starts upon completion of preheating.

2. Temporary cancellation

To cancel the power save mode temporarily on the

printer, press	RESET	, then	ENTER	to initialize the printer.

3. Permanent cancellation

Cancel the power save mode temporarily as described in step 2, and change the power save mode setting to OFF.

34

Image 34

Contents Prima Relating to electromagnetic compatibility 89/336/EEC2006/95/EC Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause 35% to 70% InstallationTo 86 F Names of parts AccessoryPower input jack Front Slide knobSet-up Connecting the IC unit Sold separatelyConnecting the Laminator Please ask your dealer for the Compact IC unit connectionPin Connecting cable Connecting the power cordInstall the unit connecting cable.optional Check the plug For AC 120V typeCard stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle Portion B See the description in Jam Transfer on p.50Setting the ink ribbon Close the printer door When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmInsert the retransfer film into the cassette Remove the retransfer film cassetteOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsThis 300 pieces is not a guaranteed quantity Shown in the illustrationWhen moving the card bracket Dealer For a magnetic or IC card, encoding error may happenConsult your dealer to purchase new gloves For ISO cards Printing on cards with magnetic strips is not guaranteedFor JIS II cards See p.34 in this manualConnecting with Ethernet cable Connecting with a host computerConnecting with USB cable Connect the printer and host computer with the USB cableWhen connecting a host computer to multiple printers Connecting Multiple PrintersCopyright of the Software is displayed Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentOperation Turning on the powerTurn the power on Represents on and O represents OFF Operation display LED Ready LED will light upAbout the Reset button Turning off the powerIs loaded User modes User mode screen flowPress Submenu To the next Main menu SubmenuDisplay mode settings Clearing the free counter Reset the free counterPress to reset Exit userSet the K printing mode2 Ink mode settingUV ink level setting Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerBend remedy speed settings Setting the bend remedy modeSet the bend remedy roller temperature To select the setting value and pressNon-contact IC antenna setting mode Card Thickness setting mode IC contact setting modeCoercivity setting mode Unit No. SettingNetwork setting Input method Address Setting mode Download mode setting Low temperature stand-by mode settingSet position of MAC address print Open the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.14, 16 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.31 in this manualSet a cleaning card Cleaning the magnetic headConfirm that the retransfer film cassette has been removed Once printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance All rollers require routine cleaning TroubleshootingCleaning unit Layout of rollers inside the printerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsFront view External appearance and dimensionsCase of disposal 34.3 38.1Ultra Electronics Card Systems