Ultra electronic Prima 3 user manual Injury Retransfer section Jam transfer

Page 50

Troubleshooting (continued)

Turnover section [Jam (turnover)]

1. Open the printer door and remove the ink ribbon cassette.

See p.14 in this manual.

2. Remove any jammed cards.

• If you can pull out the jammed cards, take them out.

•If the jammed cards come out of the turnover table, push them back into the table, and rotate the table slowly (as it is positioned vertically) until the table is located so that the cards can be taken out.

CAUTION

•When rotating the turnover table, be careful not to touch the metal edge. Wear a glove for this work.

Injury

Retransfer section [Jam (transfer)]

1. Open the printer door and remove the retransfer film cassette.

See p.16 in this manual.

2. A jog lever are supplied as standard.

The jog lever are attached to the center of the card tray

.	Jog lever

Turn the tabs in the arrow direction and take out the jog lever and removal stick.

3. Turn the jog dial to move the card to the position where it becomes visible.

Turn the jog dial with the attached jog lever.

4. Remove the card.

Remove the card.

CAUTION

Some parts inside the printer may be hot. Be careful when removing the card.

50

Image 50

Contents Prima Relating to electromagnetic compatibility 89/336/EEC2006/95/EC Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause To 86 F Installation35% to 70% Names of parts AccessoryPower input jack Front Slide knobSet-up Connecting the IC unit Sold separatelyConnecting the Laminator Please ask your dealer for the Compact IC unit connectionPin Connecting cable Connecting the power cordInstall the unit connecting cable.optional Check the plug For AC 120V typeCard stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle Portion B See the description in Jam Transfer on p.50Setting the ink ribbon Close the printer door When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmInsert the retransfer film into the cassette Remove the retransfer film cassetteOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsThis 300 pieces is not a guaranteed quantity Shown in the illustrationConsult your dealer to purchase new gloves Dealer For a magnetic or IC card, encoding error may happenWhen moving the card bracket For ISO cards Printing on cards with magnetic strips is not guaranteedFor JIS II cards See p.34 in this manualConnecting with Ethernet cable Connecting with a host computerConnecting with USB cable Connect the printer and host computer with the USB cableCopyright of the Software is displayed Connecting Multiple PrintersWhen connecting a host computer to multiple printers Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentOperation Turning on the powerTurn the power on Represents on and O represents OFF Operation display LED Ready LED will light upIs loaded Turning off the powerAbout the Reset button Press User mode screen flowUser modes Submenu To the next Main menu SubmenuDisplay mode settings Clearing the free counter Reset the free counterPress to reset Exit userSet the K printing mode2 Ink mode settingUV ink level setting Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerBend remedy speed settings Setting the bend remedy modeSet the bend remedy roller temperature To select the setting value and pressNon-contact IC antenna setting mode Card Thickness setting mode IC contact setting modeCoercivity setting mode Unit No. SettingNetwork setting Input method Address Setting mode Set position of MAC address print Low temperature stand-by mode settingDownload mode setting Open the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.14, 16 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.31 in this manualConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card Periodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed All rollers require routine cleaning TroubleshootingCleaning unit Layout of rollers inside the printerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsFront view External appearance and dimensionsCase of disposal 34.3 38.1Ultra Electronics Card Systems