Ultra electronic Prima 3 user manual Cleaning of the bobbin holders, Periodical Maintenance

Page 44

Care and Cleaning

(continued)

 

 

 

 

 

 

5.Set the card on the card tray. Place the card in right direction. See p.20.

6. Press the ENTER button, select “MG Head” with the or button, and press the ENTER button.

> > M G H e a d

O K ?

ENTER

C l e a n i n g . .

7. When the cleaning card is discharged from NG card discharge slot, turn off the power of the printer. Wait for 10 seconds before turning on the power again.

CAUTION

Replace the magnetic head cleaning card when it gets dirty. A dirty card may pollute the head

and cause damages to the head.

Consult your dealer on the alcohol and cleaning card.

Cleaning of the bobbin holders

Dirt on the bobbin holders may appear on the card or the film, cause defects on the card. Clean the bobbins when replacing ink ribbon or retransfer film.

1. Remove the cassettes of ink ribbon and retransfer film.

See p.14 and 16 of this manual.

2. Wipe 4 bobbin holders with “Kim-Wipe” soaked with absolute alcohol(ethanol)

Once printer servicing and cleaning

have been completed

Once servicing and cleaning of the printer have been completed, check to make sure that all parts have been replaced properly.

Improper replacement of parts may result in the power not turning on or in operating errors.

Periodical Maintenance

Periodical maintenance by the service personnel is recommended to avoid print error and failure. Consult your dealer for maintenance period and cost.

44

Image 44
Contents Prima 89/336/EEC 2006/95/ECRelating to electromagnetic compatibility Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with waterDo not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsEscape Clause To 86 F Installation35% to 70% Accessory Power input jackNames of parts Front Slide knobConnecting the IC unit Sold separately Connecting the LaminatorSet-up Please ask your dealer for the Compact IC unit connectionConnecting the power cord Install the unit connecting cable.optionalPin Connecting cable Check the plug For AC 120V typeInstalling the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately Portion B See the description in Jam Transfer on p.50Setting the ink ribbon When the ink ribbon is wound up to the end Wind the ribbon, taking up the slackClose the printer door Insert the cassette along the guide railSetting the retransfer film Insert the retransfer film into the cassetteOtherwise the printer may fail Slowly Remove the retransfer film cassetteWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properlySetting cards This 300 pieces is not a guaranteed quantityCassette and/or the ink ribbon cassette Shown in the illustrationConsult your dealer to purchase new gloves Dealer For a magnetic or IC card, encoding error may happenWhen moving the card bracket Printing on cards with magnetic strips is not guaranteed For JIS II cardsFor ISO cards See p.34 in this manualConnecting with a host computer Connecting with USB cableConnecting with Ethernet cable Connect the printer and host computer with the USB cableCopyright of the Software is displayed Connecting Multiple PrintersWhen connecting a host computer to multiple printers Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentTurning on the power Turn the power on Represents on and O represents OFFOperation Operation display LED Ready LED will light upIs loaded Turning off the powerAbout the Reset button Press User mode screen flowUser modes Submenu To the next Main menu SubmenuDisplay mode settings Reset the free counter Press to resetClearing the free counter Exit userInk mode setting UV ink level settingSet the K printing mode2 Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerSetting the bend remedy mode Set the bend remedy roller temperatureBend remedy speed settings To select the setting value and pressCard Thickness setting mode IC contact setting mode Coercivity setting modeNon-contact IC antenna setting mode Unit No. SettingNetwork setting Input method Address Setting mode Set position of MAC address print Low temperature stand-by mode settingDownload mode setting Careandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card trayCleaning the thermal head Cleaning the fan filterSee p.14, 16 in this manual Wipe the head indicated withCleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.31 in this manualConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card Periodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Troubleshooting Cleaning unitAll rollers require routine cleaning Layout of rollers inside the printerError code listing To initialize the unitHardware error ErrorMG connection error MG mechanical errorStopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsExternal appearance and dimensions Case of disposalFront view 34.3 38.1Ultra Electronics Card Systems