Ultra electronic Prima 3 user manual Cleaning the magnetic head, Set a cleaning card

Page 43
Cleaning card (accessory)

(to the next page)

5.Set a cleaning card.

Peel off the protective paper of the cleaning card and insert it into the NG card discharge slot. The card will be drawn into the unit by the rollers and cleaning will then be carried out from card discharge slot on the left side

of the printer. Insert the card with its adhesive face upside down to repeat the cleaning procedure once more.

The cleaning card can be inserted only from the right side.

NG card discharge slot

CAUTION

• If the retransfer roller (heat roller)

gets too hot,

H R i s t o o h o t !

appears on the LCD panel, and the printer returns to the Ready state.

Turn off the power of the printer, and wait until the roller completely cools down before starting the work.

Confirm that the retransfer film cassette has been removed.

The cleaning card does not go into the card discharge slot at the left side.

If a card jam occurs, turn off the power, then turn on the power again. The jammed card will be discarded.

6.Turn off the power after the cleaning card is discharged.

Wait for 10 seconds before turning on the power again.

CAUTION

The cleaning card can be used only once and disposable after using. If you use the dirty cleaning card many times, the dirt on the card moves

onto the rollers, causing damages to the rollers. Consult your dealer for the cleaning card.

Cleaning the magnetic head

Dirty magnetic head will cause a write/read error. It is recommended to clean the magnetic head after printing about 1,000 cards. Cleaning the magnetic head is not necessary if the magnetic stripe card is not used.

1. Keep the ink ribbon and retransfer film cassettes in their mounting positions.

2. Confirm that the READY LED (Green) is lighted

3. Specify the “cleaning” mode in the user mode.

See p.31 in this manual.

> U s e r M o d e

MENU

> C l e a n i n g >

4. Apply alcohol on the magnetic head cleaning card. Drip three or four drops of alcohol on the magnetic stripes.

Alcohol (sold separately)

Magnetic head cleaning card (sold separately)

43

Image 43
Contents Prima Harmonized Standards 89/336/EEC2006/95/EC Relating to electromagnetic compatibilityOperation is subject to the following two conditions Information for USAContents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructedDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it outHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useEscape Clause 35% to 70% InstallationTo 86 F Front Slide knob AccessoryPower input jack Names of partsPlease ask your dealer for the Compact IC unit connection Connecting the IC unit Sold separatelyConnecting the Laminator Set-upCheck the plug For AC 120V type Connecting the power cordInstall the unit connecting cable.optional Pin Connecting cablePortion B See the description in Jam Transfer on p.50 Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximatelySetting the ink ribbon Insert the cassette along the guide rail When the ink ribbon is wound up to the endWind the ribbon, taking up the slack Close the printer doorRemove the retransfer film cassette Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyIf the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteShown in the illustration Setting cardsThis 300 pieces is not a guaranteed quantity Cassette and/or the ink ribbon cassetteWhen moving the card bracket Dealer For a magnetic or IC card, encoding error may happenConsult your dealer to purchase new gloves See p.34 in this manual Printing on cards with magnetic strips is not guaranteedFor JIS II cards For ISO cardsConnect the printer and host computer with the USB cable Connecting with a host computerConnecting with USB cable Connecting with Ethernet cableWhen connecting a host computer to multiple printers Connecting Multiple PrintersCopyright of the Software is displayed Names of parts on the operation panel BeforeuseLCD operation display content Operation display LED contents LCD panelOperation display LED Ready LED will light up Turning on the powerTurn the power on Represents on and O represents OFF OperationAbout the Reset button Turning off the powerIs loaded User modes User mode screen flowPress Submenu Main menu Submenu To the nextDisplay mode settings Exit user Reset the free counterPress to reset Clearing the free counterSpecial ink SP-Ink 2 level Ink mode settingUV ink level setting Set the K printing mode2Retransfer mode setting Exit user mode Set the buzzer Buzzer mode settingTo select the setting value and press Setting the bend remedy modeSet the bend remedy roller temperature Bend remedy speed settingsUnit No. Setting Card Thickness setting mode IC contact setting modeCoercivity setting mode Non-contact IC antenna setting modeNetwork setting Input method Address Setting mode Download mode setting Low temperature stand-by mode settingSet position of MAC address print Close the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unitWipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.14, 16 in this manualSee p.31 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown belowSet a cleaning card Cleaning the magnetic headConfirm that the retransfer film cassette has been removed Once printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance Layout of rollers inside the printer TroubleshootingCleaning unit All rollers require routine cleaningTo initialize the unit Error code listingMG mechanical error Hardware errorError MG connection errorMending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not completeHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Main specifications Specifications34.3 38.1 External appearance and dimensionsCase of disposal Front viewUltra Electronics Card Systems