Ultra electronic Prima 3 user manual Escape Clause

Page 8

Before use

(continued)

 

 

Storing and handling cards after printing

Avoid storing the cards in locations exposed to direct sunlight or with high temperature and high humidity. Furthermore, avoid contact with the following chemicals and stationery, as they can cause discoloration or fading of the cards:

Organic solvents such as alcohol, film cleaner, diazo copies, etc.

Soft vinyl chlorides, document cases, pass holders, erasers, etc.

Hair-dressing products and cosmetics, etc.

Purchasing print media and cards

Contact your dealer regarding the purchase of print media (retransfer film and ink ribbons) and cards. Always use the products specified below.

Print media

Use only the ink ribbons and retransfer film specified for this unit. For the names of these products refer to “Main Specifications” on p. 51 of this manual.

CAUTION

We can accept no liability for any problems arising as a result of the use of media using materials other than those specified.

Card material

ISO/IEC 7810 type ID1 (dimensions) :

 

equivalent product

ISO/IEC 7811-2 (Magnetic stripe) :

 

 

equivalent product

ISO/IEC 7816 (IC card) :

equivalent product

The materials of some cards may not be suitable for printing. Consult your dealer regarding the materials to be used and specifications required before purchase.

Escape Clause

We do not provide compensation for any malfunction during card printing caused by breakdown of the machine, ink ribbon defects or card characteristics. In addition, we also do not provide compensation for insufficient print quality, which are not agreed in advance. Please evaluate carefully beforehand.

￿Card Material

Some card material may not be suitable for printing. Using a contact-type IC card other than those specified by the dealer, may cause damage to the thermal head.

No compensation is made for the life reduction and failures that were caused by unsuitable card material. Warp of card or uneven thickness of IC cards, even though they are within the tolerance of JIS or ISO standards, may not be suitable for printing or feeding. For details on the specifications about card material or others, consult the dealer in advance

￿Version upgrade

The following defects may occur as a result of the version upgrade for the firmware of the printer or for the printer driver.

Card printing is disabled for the application software that has been used.

The operation of the printer or application software becomes unstable.

Defects in print result occurs.

Print color or shade differs.

The performance of reproducing fine letters, changes.

Others

Be sure to retain a copy of the current version when performing version upgrade. Reinstall the previous version immediately if these problems occur. We are not liable for any damage such as defective cards or interruptions during printing as a result of the version upgrade.

8

Image 8
Contents Prima 89/336/EEC 2006/95/ECRelating to electromagnetic compatibility Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with waterDo not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsEscape Clause To 86 F Installation35% to 70% Accessory Power input jackNames of parts Front Slide knobConnecting the IC unit Sold separately Connecting the LaminatorSet-up Please ask your dealer for the Compact IC unit connectionConnecting the power cord Install the unit connecting cable.optionalPin Connecting cable Check the plug For AC 120V typeInstalling the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately Portion B See the description in Jam Transfer on p.50Setting the ink ribbon When the ink ribbon is wound up to the end Wind the ribbon, taking up the slackClose the printer door Insert the cassette along the guide railSetting the retransfer film Insert the retransfer film into the cassetteOtherwise the printer may fail Slowly Remove the retransfer film cassetteWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properlySetting cards This 300 pieces is not a guaranteed quantityCassette and/or the ink ribbon cassette Shown in the illustrationConsult your dealer to purchase new gloves Dealer For a magnetic or IC card, encoding error may happenWhen moving the card bracket Printing on cards with magnetic strips is not guaranteed For JIS II cardsFor ISO cards See p.34 in this manualConnecting with a host computer Connecting with USB cableConnecting with Ethernet cable Connect the printer and host computer with the USB cableCopyright of the Software is displayed Connecting Multiple PrintersWhen connecting a host computer to multiple printers Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentTurning on the power Turn the power on Represents on and O represents OFFOperation Operation display LED Ready LED will light upIs loaded Turning off the powerAbout the Reset button Press User mode screen flowUser modes Submenu To the next Main menu SubmenuDisplay mode settings Reset the free counter Press to resetClearing the free counter Exit userInk mode setting UV ink level settingSet the K printing mode2 Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerSetting the bend remedy mode Set the bend remedy roller temperatureBend remedy speed settings To select the setting value and pressCard Thickness setting mode IC contact setting mode Coercivity setting modeNon-contact IC antenna setting mode Unit No. SettingNetwork setting Input method Address Setting mode Set position of MAC address print Low temperature stand-by mode settingDownload mode setting Careandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card trayCleaning the thermal head Cleaning the fan filterSee p.14, 16 in this manual Wipe the head indicated withCleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.31 in this manualConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card Periodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Troubleshooting Cleaning unitAll rollers require routine cleaning Layout of rollers inside the printerError code listing To initialize the unitHardware error ErrorMG connection error MG mechanical errorStopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsExternal appearance and dimensions Case of disposalFront view 34.3 38.1Ultra Electronics Card Systems