Ultra electronic Prima 3 user manual For JIS II cards, For ISO cards, See p.34 in this manual

Page 20

Set-up(continued)

When using magnetic cards

When using cards with magnetic strips, set the cards in the following manner.

For JIS II cards:

Place the card with its magnetic stripes upward and facing the card bracket.

For ISO cards:

Place the card with its magnetic stripes downward and facing the card bracket.

CAUTION

Printing on cards with magnetic strips is not guaranteed.

When using contact IC cards

When using contact IC cards, set in the following manner.

Place the IC card with its IC terminal inward and facing the card bracket.

Loading cards

Load cards when the printer’s LCD panel shows the message “Ready” or “No Card”, and not when printer operations have stopped due to an error. Cards can

also be loaded when the power supply is not switched on. If there is a drop in the volume of remaining cards (under about 25 cards with a thickness of 0.76mm), the electronic beep sounds before every feeding.

(See p.34 in this manual.)

R e a d y

N o C a r d

OR

L o a d i n g

When “Loading” is displayed on the LCD panel, do not open the card tray under any circumstances.

The unit is currently feeding cards. If a message other than the one above is displayed, cards can be loaded even while the unit is printing. However, you are recommended to load cards when the unit is not printing.

To prevent defective printing caused by suspended printing or vibration as a result of opening and closing the card tray, load cards with care.

Switching the card thickness

Depending on the material, some 0.25mm(0.01inches) thick cards may not be suitable for printing. Consult your dealer regarding the materials and specifications

of the card before purchasing.

WARNING

As for switching the card thickness,consult your dealer or the service personnel. Otherwise injuries or malfunction of the printer may be caused

Electric shock

Injury

20

Image 20
Contents Prima 89/336/EEC 2006/95/ECRelating to electromagnetic compatibility Harmonized StandardsInformation for USA Operation is subject to the following two conditionsContents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with waterDo not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsEscape Clause To 86 F Installation35% to 70% Accessory Power input jackNames of parts Front Slide knobConnecting the IC unit Sold separately Connecting the LaminatorSet-up Please ask your dealer for the Compact IC unit connectionConnecting the power cord Install the unit connecting cable.optionalPin Connecting cable Check the plug For AC 120V typeInstalling the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately Portion B See the description in Jam Transfer on p.50Setting the ink ribbon When the ink ribbon is wound up to the end Wind the ribbon, taking up the slackClose the printer door Insert the cassette along the guide railSetting the retransfer film Insert the retransfer film into the cassetteOtherwise the printer may fail Slowly Remove the retransfer film cassetteWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properlySetting cards This 300 pieces is not a guaranteed quantityCassette and/or the ink ribbon cassette Shown in the illustrationConsult your dealer to purchase new gloves Dealer For a magnetic or IC card, encoding error may happenWhen moving the card bracket Printing on cards with magnetic strips is not guaranteed For JIS II cardsFor ISO cards See p.34 in this manualConnecting with a host computer Connecting with USB cableConnecting with Ethernet cable Connect the printer and host computer with the USB cableCopyright of the Software is displayed Connecting Multiple PrintersWhen connecting a host computer to multiple printers Beforeuse Names of parts on the operation panelOperation display LED contents LCD panel LCD operation display contentTurning on the power Turn the power on Represents on and O represents OFFOperation Operation display LED Ready LED will light upIs loaded Turning off the powerAbout the Reset button Press User mode screen flowUser modes Submenu To the next Main menu SubmenuDisplay mode settings Reset the free counter Press to resetClearing the free counter Exit userInk mode setting UV ink level settingSet the K printing mode2 Special ink SP-Ink 2 levelRetransfer mode setting Buzzer mode setting Exit user mode Set the buzzerSetting the bend remedy mode Set the bend remedy roller temperatureBend remedy speed settings To select the setting value and pressCard Thickness setting mode IC contact setting mode Coercivity setting modeNon-contact IC antenna setting mode Unit No. SettingNetwork setting Input method Address Setting mode Set position of MAC address print Low temperature stand-by mode settingDownload mode setting Careandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card trayCleaning the thermal head Cleaning the fan filterSee p.14, 16 in this manual Wipe the head indicated withCleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.31 in this manualConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card Periodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Troubleshooting Cleaning unitAll rollers require routine cleaning Layout of rollers inside the printerError code listing To initialize the unitHardware error ErrorMG connection error MG mechanical errorStopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Main specificationsExternal appearance and dimensions Case of disposalFront view 34.3 38.1Ultra Electronics Card Systems