PSC SP400rf manual Contents

Page 3

Contents

 

Introduction

 

I Need to Understand the Basics

1

Integrating Peripherals With Host Systems

1

Changing Interfaces

2

Customizing Your Scanner Operation

3

Programming Overview

4

What Is Programming Mode?

4

How To Program Using Barcodes

4

The Programming Session

5

Scanner Response When In Programming Mode ....

5

If You Make a Mistake

6

Return to Factory Settings

6

Configuration Upload

6

Where To Go From Here

7

Interface Selection

 

IBM

 

IBM 4683/84 • 4693/94 Port 5B I/F Selection

8

IBM 4683/84 • 4693/94 Port 9A, 9B,

 

9C, 9E I/F Selection

9

IBM 4682/92 Port E Interface Selection

10

OCIA

 

PSC OCIA Interface Selection

11

NCR OCIA Eight Bit (short format) I/F Selection ....

11

NCR OCIA Nine Bit (long format) I/F Selection

11

SNI OCIA Interface Selection

11

OCIA Options

12

Wand

 

Wand Emulation Interface Selection

13

R44-1027

i

Image 3
Contents Handheld Laser Scanner Disclaimer PSC Scanning, IncContents RS-232 Iii SP400RF Programming Guide Integrating Peripherals with Host Systems Need to Understand the BasicsSP400RF Interface Groups Changing InterfacesCustomizing Your Scanner Operation What is Programming MODE? HOW to Program Using BarcodesProgramming Overview Programming Session Scanner Response When in Programming ModeEND Return to Factory SettingsConfiguration Upload SETWhere to GO from Here IBM 4683/84 4693/94 Port 5B Interface SELECTION1 IBM 4683/84 4693/94 Port 5B SettingsSET Send AS Code IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E SettingsIBM 4682/92 Port E Interface Selection IBM 4682/92 Port E SettingsPSC1 Ocia Interface Selection NCR Ocia Nine BIT Long Format Interface SelectionSNI Ocia Interface Selection Nable Isable SETNable IsableWand Emulation Interface Selection Full AsciiEND LOWHigh C128Communication Parameter RS-232 Interface SelectionSNI RS-232 Interface Selection Data Bits Start Bit Parity Bits Stop Bits Data Format Settings Hardware Control Software Control SET = N ONE = 90 Milliseconds = 100 Milliseconds Type PC Keyboard Wedge Interface SelectionEyboard Wedge Interface Intercharacter Delay = 55 Milliseconds STI Keyboard Wedge Interface Selection Ibmxxxx STI WedgeLabel Transmit Format Configuration Items RS-232AND Keyboard Wedge Interfaces onlyPrefix & Suffix Label Transmit Format Config For the example in step four, scan 0, 2, 2 SET SET PrefixFor the example in step five, scan 0, 7, 0 SET SET SuffixSetting a Single Character Prefix or Suffix ONE Character only Ascii Character SET ~ 7E DelUPC-A Our example, we would scan the UPC-A symbology label EAN-13 UPC-AUPC-E EAN-8Code Codabar Interleaved 2 Standard 2 MSI/PLESSEY Scan the barcodes values Disabling Label I.D. for a Specific Symbology Label Transmit Format Config Interface Type UPC/EANCode Symbology Options Overview Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology SelectionEnable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable CodeUPC/EAN Options UPC/EAN Expansion Disabled END OptionalRequired UPC-E Sendcheck DigitSend Check Digit SET EAN-8PRICE/WEIGHT Check Digit Code 39 Options Ascii Scan the Set Code 39 Minimum Label Length barcode Code 39 Minimum Label Length Interleaved 2 Compute EnableDisable SET Dont ComputeScan the Enable First Fixed barcode SET Fixed Engths Standard 2 Normal or Iata Selection Iata Standard 2Dont Compute Dont Transmit Enable Disable Scan the Enable First Fixed barcode Standard 2 of 5 Fixed and Minimum Label Lengths Codabar Options Codabar Check Digit & Variable Length TRANSMIT1 Format = abcd/tn*eCodabar START/STOP Character SET Codabar Fixed LengthScan the Set Second Fixed Length label ONE Check Digit TWO Check DigitsMSI/PLESSEY Check Digit MSI/PLESSEY Fixed Length MSI/PLESSEY SET Fixed Lengths Code 128 Options General Features Communications Protocol General FeaturesEND Enable DisableACK/NAK Item on Not on FileSTX/ETX Ascii BCDSET STX SET ETX SET SET STX/ETX ENDWhen to Acknowledge Wack Wack ACK RS-232 Feature onlyOption ① Option ➁ Option ➂ SYNC2 When to Beep OptionsNAK Wack ACK NAK SET Ption Beeper Volume OptionNormal Loud Radio Channel Frequency ChannelRadio Transmit Power Wait Time Wait Time for Host AcknowledgeWait Time for Host Acknowledge Verify EAN-13 Verify UPC-AVerify UPC-E Verify EAN-8ONE Read TWO Reads Three Reads Four Reads Verify CodeVerify Codabar Verify Code Verify MSI/PLESSEYBeep Twice No Beep LOW Battery Indication MethodUPC/EAN Factory DefaultsEnable DisableCode High Disable Item ON/OFF FileACK/NAK Protocol ETX/STXONE INTERFACE-DISCRETE DefaultsRS-232/KEYBOARD Wedge NoneIBM Interfaces 100Host Programming Creating Multifunction LabelsNeed More Information 102 MSI/PLESSEY UPC-A W/2 Digit ADD-ON UPC-A W/ 5 Digit ADD-ON UPC-E EAN-8104 Blank Germany Asia PacificAustralia France