PSC SP400rf manual Verify UPC-A, Verify UPC-E, Verify EAN-8, Verify EAN-13, Read Verification

Page 99

READ VERIFICATION

SP400RF programming has been improved to allow selection of read verification "minimum read" requirements by symbology type, rather than universally. This means that the scanner needn't waste valuable time verifying high-confidence symbologies, while offering the security of multiple read verification on less reliable codes.

NOTE

The more times the scanner is required to read and compare the barcode data, the longer it will take to complete a good read cycle.

To set the minimum read requirement for a desired symbology:

1.Scan the SET label.

2.Scan one symbology label below to select the symbology to be verified.

3.Scan the label on the following page representing the amount of times you wish a barcode label of that symbology type to be read before transmission to the host

4.Repeat steps one through three above until read verification has been selected for all symbologies you desire to be verified.

5.Scan the END label.

SET

-------------------------------------

YPE

 

VERIFY UPC-A ---------------

T

 

 

SYMBOLOGY

 

VERIFY UPC-E ---------------

VERIFICATION

 

VERIFY EAN-8 ---------------

 

 

READ

 

VERIFY EAN-13 --------------

 

 

 

 

VERIFY INSTORE LABEL ---------

 

 

 

GENERAL FEATURES

R44-1027

93

Page 98 Page 100
Image 99
Page 98 Page 100
Contents Handheld Laser Scanner Disclaimer PSC Scanning, IncContents RS-232 Iii SP400RF Programming Guide Integrating Peripherals with Host Systems Need to Understand the BasicsSP400RF Interface Groups Changing InterfacesCustomizing Your Scanner Operation What is Programming MODE? HOW to Program Using BarcodesProgramming Overview Programming Session Scanner Response When in Programming ModeEND Return to Factory SettingsConfiguration Upload SETWhere to GO from Here IBM 4683/84 4693/94 Port 5B Interface SELECTION1 IBM 4683/84 4693/94 Port 5B SettingsSET Send AS Code IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E SettingsIBM 4682/92 Port E Interface Selection IBM 4682/92 Port E SettingsPSC1 Ocia Interface Selection NCR Ocia Nine BIT Long Format Interface SelectionSNI Ocia Interface Selection Nable Isable SETNable IsableWand Emulation Interface Selection Full AsciiEND LOWHigh C128Communication Parameter RS-232 Interface SelectionSNI RS-232 Interface Selection Data Bits Start Bit Parity Bits Stop Bits Data Format Settings Hardware Control Software Control SET = N ONE = 90 Milliseconds = 100 Milliseconds Type PC Keyboard Wedge Interface SelectionEyboard Wedge Interface Intercharacter Delay = 55 Milliseconds STI Keyboard Wedge Interface Selection Ibmxxxx STI WedgeLabel Transmit Format Configuration Items RS-232AND Keyboard Wedge Interfaces onlyPrefix & Suffix Label Transmit Format Config For the example in step four, scan 0, 2, 2 SET SET PrefixFor the example in step five, scan 0, 7, 0 SET SET SuffixSetting a Single Character Prefix or Suffix ONE Character only Ascii Character SET ~ 7E DelUPC-A Our example, we would scan the UPC-A symbology label EAN-13 UPC-AUPC-E EAN-8Code Codabar Interleaved 2 Standard 2 MSI/PLESSEY Scan the barcodes values Disabling Label I.D. for a Specific Symbology Label Transmit Format Config Interface Type UPC/EANCode Symbology Options Overview Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology SelectionEnable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable CodeUPC/EAN Options UPC/EAN Expansion Disabled END OptionalRequired UPC-E Sendcheck DigitSend Check Digit SET EAN-8PRICE/WEIGHT Check Digit Code 39 Options Ascii Scan the Set Code 39 Minimum Label Length barcode Code 39 Minimum Label Length Interleaved 2 Compute EnableDisable SET Dont ComputeScan the Enable First Fixed barcode SET Fixed Engths Standard 2 Normal or Iata Selection Iata Standard 2Dont Compute Dont Transmit Enable Disable Scan the Enable First Fixed barcode Standard 2 of 5 Fixed and Minimum Label Lengths Codabar Options Codabar Check Digit & Variable Length TRANSMIT1 Format = abcd/tn*eCodabar START/STOP Character SET Codabar Fixed LengthScan the Set Second Fixed Length label ONE Check Digit TWO Check DigitsMSI/PLESSEY Check Digit MSI/PLESSEY Fixed Length MSI/PLESSEY SET Fixed Lengths Code 128 Options General Features Communications Protocol General FeaturesEND Enable DisableACK/NAK Item on Not on FileSTX/ETX Ascii BCDSET STX SET ETX SET SET STX/ETX ENDWhen to Acknowledge Wack Wack ACK RS-232 Feature onlyOption ① Option ➁ Option ➂ SYNC2 When to Beep OptionsNAK Wack ACK NAK SET Ption Beeper Volume OptionNormal Loud Radio Channel Frequency ChannelRadio Transmit Power Wait Time Wait Time for Host AcknowledgeWait Time for Host Acknowledge Verify EAN-13 Verify UPC-AVerify UPC-E Verify EAN-8ONE Read TWO Reads Three Reads Four Reads Verify CodeVerify Codabar Verify Code Verify MSI/PLESSEYBeep Twice No Beep LOW Battery Indication MethodUPC/EAN Factory DefaultsEnable DisableCode High Disable Item ON/OFF FileACK/NAK Protocol ETX/STXONE INTERFACE-DISCRETE DefaultsRS-232/KEYBOARD Wedge NoneIBM Interfaces 100Host Programming Creating Multifunction LabelsNeed More Information 102 MSI/PLESSEY UPC-A W/2 Digit ADD-ON UPC-A W/ 5 Digit ADD-ON UPC-E EAN-8104 Blank Germany Asia PacificAustralia France
Top Page Image Contents