PSC SP400rf manual Interface Type, Upc/Ean, Code

Page 47

SYMBOLOGIES

Symbology selection (barcode type) determines which symbologies the scanner will decode. The chart below shows the symbologies that are supported by each interface. Once you have identified the symbologies you wish to enable, turn to the following pages, enable those symbologies and set the data format options (e.g. check digit, start/stop characters) required by your host system for each symbology type. You must enable the symbology format options settings that are compatible with your host system.

The factory settings for each interface were chosen to meet the standard industry requirements and in most cases you will not need to change the symbology format settings. If you are unsure of your system require- ments, test the scanner using the factory settings before making any changes.

		SYMBOLOGIES
			SUPPORTED
INTERFACE TYPE	UPC/EAN	Code 39	Inter. 2 of 5 Std 2 of 5 Codabar Code 93 Code 128	MSI/Plessey
INTERFACE TYPE

IBM Port 5B

IBM Port 9B

IBM Port E

NCR OCIA (8 bit)

NCR OCIA (9 bit)

S-P OCIA

SNI OCIA

RS-232

Wand Emulation

Keyboard Wedge

SYMBOLOGY SELECTION

R44-1027

41

Image 47

Contents Handheld Laser Scanner Disclaimer PSC Scanning, IncContents RS-232 Iii SP400RF Programming Guide Integrating Peripherals with Host Systems Need to Understand the BasicsSP400RF Interface Groups Changing InterfacesCustomizing Your Scanner Operation Programming Overview What is Programming MODE?HOW to Program Using Barcodes Programming Session Scanner Response When in Programming ModeEND Return to Factory SettingsConfiguration Upload SETWhere to GO from Here IBM 4683/84 4693/94 Port 5B Interface SELECTION1 IBM 4683/84 4693/94 Port 5B SettingsSET Send AS Code IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E SettingsIBM 4682/92 Port E Interface Selection IBM 4682/92 Port E SettingsSNI Ocia Interface Selection PSC1 Ocia Interface SelectionNCR Ocia Nine BIT Long Format Interface Selection Nable Isable SETNable IsableWand Emulation Interface Selection Full AsciiEND LOWHigh C128SNI RS-232 Interface Selection Communication ParameterRS-232 Interface Selection Data Bits Start Bit Parity Bits Stop Bits Data Format Settings Hardware Control Software Control SET = N ONE = 90 Milliseconds = 100 Milliseconds Type PC Keyboard Wedge Interface SelectionEyboard Wedge Interface Intercharacter Delay = 55 Milliseconds STI Keyboard Wedge Interface Selection Ibmxxxx STI WedgePrefix & Suffix Label Transmit Format Configuration ItemsRS-232AND Keyboard Wedge Interfaces only Label Transmit Format Config For the example in step four, scan 0, 2, 2 SET SET PrefixFor the example in step five, scan 0, 7, 0 SET SET SuffixSetting a Single Character Prefix or Suffix ONE Character only Ascii Character SET ~ 7E DelUPC-A Our example, we would scan the UPC-A symbology label EAN-13 UPC-AUPC-E EAN-8Code Codabar Interleaved 2 Standard 2 MSI/PLESSEY Scan the barcodes values Disabling Label I.D. for a Specific Symbology Label Transmit Format Config Code Interface TypeUPC/EAN Symbology Options Overview Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology SelectionEnable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable CodeUPC/EAN Options UPC/EAN Expansion Required Disabled ENDOptional UPC-E Sendcheck DigitSend Check Digit SET EAN-8PRICE/WEIGHT Check Digit Code 39 Options Ascii Scan the Set Code 39 Minimum Label Length barcode Code 39 Minimum Label Length Interleaved 2 Compute EnableDisable SET Dont ComputeScan the Enable First Fixed barcode SET Fixed Engths Standard 2 Normal or Iata Selection Iata Standard 2Dont Compute Dont Transmit Enable Disable Scan the Enable First Fixed barcode Standard 2 of 5 Fixed and Minimum Label Lengths Codabar Options Codabar Check Digit & Variable Length Codabar START/STOP Character TRANSMIT1Format = abcd/tn*e SET Codabar Fixed LengthScan the Set Second Fixed Length label MSI/PLESSEY Check Digit ONE Check DigitTWO Check Digits MSI/PLESSEY Fixed Length MSI/PLESSEY SET Fixed Lengths Code 128 Options General Features Communications Protocol General FeaturesEND Enable DisableACK/NAK Item on Not on FileSTX/ETX Ascii BCDSET STX SET ETX SET SET STX/ETX ENDWhen to Acknowledge Wack Wack ACK RS-232 Feature onlyOption ① Option ➁ Option ➂ SYNC2 When to Beep OptionsNAK Wack ACK NAK SET Ption Normal Loud Beeper VolumeOption Radio Channel Frequency ChannelRadio Transmit Power Wait Time Wait Time for Host AcknowledgeWait Time for Host Acknowledge Verify EAN-13 Verify UPC-AVerify UPC-E Verify EAN-8ONE Read TWO Reads Three Reads Four Reads Verify CodeVerify Codabar Verify Code Verify MSI/PLESSEYBeep Twice No Beep LOW Battery Indication MethodUPC/EAN Factory DefaultsEnable DisableCode High Disable Item ON/OFF FileACK/NAK Protocol ETX/STXONE INTERFACE-DISCRETE DefaultsRS-232/KEYBOARD Wedge NoneIBM Interfaces 100Need More Information Host ProgrammingCreating Multifunction Labels 102 MSI/PLESSEY UPC-A W/2 Digit ADD-ON UPC-A W/ 5 Digit ADD-ON UPC-E EAN-8104 Blank Germany Asia PacificAustralia France