Uniden UBC3300XLT manual 50.0, Press MENU/BACK

Page 72

Setting the Base, Spacing Frequencies and Offset Channel for Motorola

VHF/UHF Trunked Systems

To properly track Motorola VHF and UHF trunked systems you must enter what is known as the base, the spacing frequencies and offset channels for each system.

To find these out, check www.bearcat1.com/free.htm and other web sites and frequency resources.

To enter the Base, Spacing Frequencies and Offset Channel: (You can set up to three sets of these, but almost all systems only use one set)

1.Press MENU/BACK.

2.Select 2:SCAN OPTION / 2:TRUNK by rotating the VFO and pressing E.

3.Select the bank number by rotating the VFO and pressing E.

4.Select 1:TRUNK TYPE /1:ON / 4:TYPE2 UHF or

5:TYPE2 VHF by rotating the VFO and pressing E.

5.Select BASE CONFIG from 1 - 3 by rotating the VFO and pressing E.

6.Enter a new Base Frequency with the keypad.

7.Press E.

The display changes for entering the Spacing Frequency.

8.Enter a new Spacing Frequency with the keypad.

M

406.0000 ENTER FREQUENCY BASE FREQUENCY 1

M

50.0

ENTER FREQUENCY SPACE FREQUENCY1

Note: You can only enter within a range of 5-100 kHz, and 5 or 7.5 or 12.5 kHz multiples.

9.Press E.

The display changes for entering the Offset Channel.

10.Enter a new Offset Channel with the keypad. The Offset Channel for the first set should be CH380.

Note: You can only input within a range of 380-759.

M

CH 380 ENTER CHANNEL OFFSET CHANNEL1

11.Press E.

The display changes for entering the Base Frequency.

12.To exit from this mode, press MENU/BACK repeatedly.

68

Image 72
Contents Page Page Contents Edacs Scat Introduction LTRFront View Icon Display Icon DescriptionUBC3300XLT Shortcuts Then enter the trunk type you want to track. Press E Important Notice What is Scanning? What is Searching?What is Trunk Tracking? TerminologyPage Feature Highlights Page Where to Obtain More Information Information on the InternetIncluded with Your Scanner Package Setup Installing the Battery PackCharging the Battery Pack Low Battery IndicatorConnecting the Optional Remote Cable Flexible AntennaBeltclip Listening SafelySetting the Squelch Basic OperationTurn the Scanner On Understanding the Menu System Menu Description and Numeric Keypad Equivalents Set attenuation for all search ranges. See 2SCAN 2SCAN Option 1CONVENTIONAL 6STEPS You can assign a variety of step sizes to the channel 8I-CALLMOTOROLA/EDACS 0EDACS ID Form Edacs 3SYSTEM Option 1DIMMER Select 2DISABLE in this mode Storing Frequencies into Channels in Menu Mode ProgrammingPress MENU/BACK Deleting a Stored Frequency Editing a Stored FrequencyDuplicate Frequency Alert 010 512.0000 FMTransfer Frequencies Storing Text TagsPress HOLD/MAN Assigning a Bank Tag to a Bank Press MENU/BACKBeep Alert 855.0000Assigning the Beep Alert to a Channel Programming Tips Scanning Storing Frequencies During Scanning001 BankRF Attenuation Feature Setting the Delay Mode for FrequencyLockout in Hold Mode Press HOLD/MAN Lockout in Scanning ModeChannel Lockout 001 141.5000 FM Uniden Group aRestoring a Locked-out Channel Restoring All Locked-out ChannelsPriority Scan Changing the Priority Channel Priority Channel Plus Scan001 512.0000 FM Setting a Search Range SearchingSrch 12.5k 1240.0000 FM Range Search Hold Feature Starting Chain SearchData Skip Srch 12.5k 1240.0000 FM Range 25cm Amateur GrpFrequency Skip Storing Search FrequenciesAuto Storing 12.5k12--56 Squelch SQ Mode 001 FM Bank001 512.0000 FM Ctcss 250.3 Bank 001 FM DCS Bank001 512.0000 FM Bank 003 512.0000 FM Ctcss Uniden Group aAdditional Menu Options for Searching Air Service Search Air Service Search SkipPress AIR/STEP Service Search AIR Programming Receiving Trunked Systems Selecting or Changing Trunking System Type001 0000.0000 Programming Trunking Frequencies LCD display Icon TrunkingType Special requirementsProgramming ID Scan Lists Manually 010M5-0 4128 1216¡ M5-0 050-2¡E5-0 09-022¡ 02-120¡ M5-01216 To enter a LTR IDReceiving Trunked Systems ID Scan Mode ID Scan 867.9875 FM ListID Scan Hold Feature ID Monitor ModeTrunked Search ID Search Hold and Direct Entry ID Hold Mode ID LockoutID4128 867.8375 FMReview ID Lockout Restoring Locked-out IDsLT ID0-02-042 To unlock a single ID, follow these steps Press MENU/BACKSetting the Delay Mode for Trunking Mode Reverse KeySetting Priority in Trunking Mode Programming Scan Lists During SearchDeleting a Stored ID Moving between Scan List Memories Call Motorola/EDACSCalls in Scan and Hold Mode Multi-TrackMulti-Track Operational Details Edacs Reception Edacs TrackingAn Edacs Trunked system SearchSpecial Edacs Features AFS Partial Entry FeaturePatch Tracking LTR Reception LTR TrackingMotorola Reception Motorola TrackingSelecting Preset Fleet Map Fleet Map Programming001 867.8375 FM 1TYPE2 800 2TYPE1 Programming a Fleet Map Programming a Hybrid System001 867.8375 FM 1TYPE2 001 FM Block 0 Size Code50.0 Control Channel Only Mode Toggling the Status BitPage Disconnect Tone Detect Option End Code PC Control Mode Remote InterfaceTo connect Scanner to PC To program your scannerClone Mode Start Remote Mode and Change Transfer SpeedSpeed 39600 bps 419200 bps PC Control ParameterTo connect the Scanner to Scanner Changer Cable available at most computer storesClone Additional Features DimmerEnter Lock Key LockReverse Mode Key Beep OptionScreen Mask Channel Step SelectionReceiving Mode Selection Frequency and Channel Tuning with the VFO ControlMute On/Off Care and Maintenance Troubleshooting Problem Suggestion Specifications Glossary of Terms Page Page Preset Fleet Maps AppendixSize Code User Defined Fleet Maps Type I Programming InformationFleet Map Size Codes Size Code RestrictionsReverse List UBC3300XLT Flow Charts Scan Option Conventional System Option Dimmer Dimmer Light Dimmer Time Screen Mask Declaration of Conformity Memo UBZZ01315AZ