Avery 206, 204, 256 manual START-UP and Shutdown, Turning on the unit, Starting label dispensing

Page 43

		CONTENTS		ALS
		CONTENTS		20x
	4.1	START-UP AND SHUTDOWN		256
	4.1	START-UP AND SHUTDOWN		GB
				GB
	4.1.1	Turning on the unit


	Set the main switch [44A] of the unit to ‘I’ (On).

–The following messages are displayed during the start process:

						A
	ALS204 RH:
	ALS204 RH:
	V 1.00

	(machine type and firmware version)

	Memory:	16 MB
	Flashcard	48 MB
	(the machine’s RAM, as well as the CF card’s
	(the machine’s RAM, as well as the CF card’s			[44] Main switch (A) of the ALS 20x
	memory, if a card is inserted)			[44] Main switch (A) of the ALS 20x
	memory, if a card is inserted)

ONLINE

Label0

–Once switched on, the ALS 20x is in dispensing mode; in other words, triggering the product sensor will cause a label to be dispensed.

–You can find more information on the dispensing mode in the section “Spendebetrieb” on page 18.

4.1.2Starting label dispensing

Dispensing with a product sensor

Once switched on, the ALS 20x is in dispensing mode; this means that triggering the product sensor will cause a label to be dispensed.

Prerequisites:

–The label length must be specified.

–The product sensor must be connected.

–The sensors must be configured correctly (PNP/NPN).

Dispensing without a product sensor

It is also possible to trigger the dispensing process without a product sensor:

–The machine is in dispensing mode:

Press the button.

–The machine is in configuration mode:

Press the button briefly (less than two seconds).

39

Image 43

Contents 204/206 256 Page Product description Please noteOperational failures Before operationAfter operation OperationValidity and binding effect of this manual General NotesParameters Signs and symbolsButton symbols Illustrations and descriptionsKeep the product information at hand Safety InstructionsInformation and qualifications Follow the instructionsProper usage Operational safety of the unitProtection against injuries by electrical current Protection against injuries by chemicals Protection against injuries by mechanical actionDue diligence of the user Before beginning productionPinch point Safety notes on the unitComponents OverviewALS 20x LCD display Error LEDControl panel Operating LEDConnections on the back of the device Connection arrangementLabel Label H Sensor connectionsMode of operation Labels Technical specificationsCharacteristics Power supplyStatus messages, test functions, product profiles ElectronicsInterfaces Internal InterfacesCertificates DimensionsEnvironmental conditions IntegrationRight-handed version Design modelsLeft-handed version Swivelling dispensing edge OptionsExternal control panel Fixed dispensing edgePneumatic dispensing edge Adjustable dispensing edge holderShape dispensing edge Applicator interface Outer Diameter control sensorPrinter ApplicatorOperating Modes Dispensing modeDispensing speed Online settingsFunction of the double-arrow button Configuration modeMenus German FunctionsFunction overview Function DescriptionsSERVICE/DIAGNOS Service Data Machine Setup menu Label Setup menuService Data menu Electrical Connections Power supply connectionConnecting the power cable Checking the power supply settingSwitch setting Permissible mains voltage C D Connecting sensorsPrerequisites ALSRemoving glue residue Inserting Label MaterialInserting a label roll Removing spent backing paperThreading guide Threading the label rollThreading the label roll at the dispensing edge Fastening the label roll to the rewinder Threading the label roll onto the drive rollerAdjusting the unwinder’s core diameter Mechanical SettingsPositioning the pressure roller Positioning the label sensor Dispensing with a product sensor START-UP and ShutdownTurning on the unit Starting label dispensingStopping the dispensing process Label stop position Configuration and MonitoringFunction menu settings Label pitchDispensing speed Configuring speed adaptionLabel position on the product 256Material end Monitoring functionsMaterial tear Missing labelsStoring a product profile Using Product ProfilesWhat are product profiles? Loading a product profileDeleting a product profile Call the Machine Setup Del. prod.profil functionActive fuse Mains voltage Switch setting Maintenance and CleaningReplacing fuses Cleaning agents Removing paper debris Regular maintenanceRenewal of the dust filter liner ALS Status Status text Cause Error MessagesReporting errors List of error messagesALS 20x Set to Dhcp Interface Para EU Declaration of Conformity Avery Dennison Deutschland GmbH