Avery 256, 204, 206 manual Operational safety of the unit, Proper usage

Page 8

CONTENTS

1.2SAFETY INSTRUCTIONS

1.2.2Operational safety of the unit

Proper usage

The ALS 20x Label Dispenser is a fully automatic unit for attaching self-adhesive labels to products or packaging. The company operating the unit must install it with suitable equipment to protect operating personnel from danger; for example, the danger of the hands or fingers being crushed by reaching in between the product and the dispensing edge.

WARNING!

Improper usage of the unit can cause accidents, property damage and production downtime!

Only use the unit in accordance with the instructions specified in this manual. Do not operate the unit without the required safeguards.

Only configure the unit in accordance with this manual and with the required care.

Only use original accessories. Do not make any modifications or alterations to the unit.

Repairs to the device may only be performed by authorised specialists who are aware of the risks involved.

Protection against injuries by electrical current

WARNING!

The machine operates using mains voltage! Touching live electrical parts may expose you to hazardous electrical currents and may lead to burns.

Only operate the unit once the housing has been reassembled properly.

Only connect the unit to a properly fitted power socket that is grounded.

Before cleaning, switch off the unit and remove the power cable from the socket. Only link the unit to devices that fulfil the SELV (safety extra-low voltage) circuit requirements specified in EN 60950.

ALS 20x 256

GB

WARNING

The unit is not protected against splashing water in its standard model.

Keep the unit dry.

If liquids have penetrated the unit, switch it off and disconnect or unplug the power cable immediately. Inform a service technician.

WARNING

The device is only completely disconnected from the mains if the power cable is unplugged.

Make sure the power supply socket is accessible.

In case of emergency, switch off the device and disconnect the power cable.

CAUTION

A too high or low supply voltage can damage the unit.

Only operate the device using the system voltage indicated on the nameplate. Ensure that the mains voltage set on the unit is the same voltage as that provided by the electricity supplier.

4

Image 8
Contents 204/206 256 Page Please note Product descriptionBefore operation After operationOperation Operational failuresGeneral Notes Validity and binding effect of this manualSigns and symbols Button symbolsIllustrations and descriptions ParametersSafety Instructions Information and qualificationsFollow the instructions Keep the product information at handProtection against injuries by electrical current Operational safety of the unitProper usage Protection against injuries by mechanical action Protection against injuries by chemicalsBefore beginning production Due diligence of the userSafety notes on the unit Pinch pointOverview ComponentsALS 20x Error LED Control panelOperating LED LCD displayConnection arrangement Connections on the back of the deviceSensor connections Label Label HMode of operation Technical specifications CharacteristicsPower supply LabelsElectronics InterfacesInternal Interfaces Status messages, test functions, product profilesDimensions Environmental conditionsIntegration CertificatesLeft-handed version Design modelsRight-handed version Options External control panelFixed dispensing edge Swivelling dispensing edgeShape dispensing edge Adjustable dispensing edge holderPneumatic dispensing edge Outer Diameter control sensor PrinterApplicator Applicator interfaceDispensing mode Operating ModesOnline settings Dispensing speedMenus Configuration modeFunction of the double-arrow button Functions GermanFunction Descriptions Function overviewSERVICE/DIAGNOS Service Data Label Setup menu Machine Setup menuService Data menu Power supply connection Electrical ConnectionsSwitch setting Permissible mains voltage Checking the power supply settingConnecting the power cable Connecting sensors C DALS PrerequisitesInserting Label Material Inserting a label rollRemoving spent backing paper Removing glue residueThreading the label roll Threading guideThreading the label roll at the dispensing edge Threading the label roll onto the drive roller Fastening the label roll to the rewinderPositioning the pressure roller Mechanical SettingsAdjusting the unwinder’s core diameter Positioning the label sensor START-UP and Shutdown Turning on the unitStarting label dispensing Dispensing with a product sensorStopping the dispensing process Configuration and Monitoring Function menu settingsLabel pitch Label stop positionConfiguring speed adaption Dispensing speed256 Label position on the productMonitoring functions Material tearMissing labels Material endUsing Product Profiles What are product profiles?Loading a product profile Storing a product profileCall the Machine Setup Del. prod.profil function Deleting a product profileReplacing fuses Maintenance and CleaningActive fuse Mains voltage Switch setting Cleaning agents Renewal of the dust filter liner ALS Regular maintenanceRemoving paper debris Error Messages Reporting errorsList of error messages Status Status text CauseALS 20x Set to Dhcp Interface Para EU Declaration of Conformity Avery Dennison Deutschland GmbH