Transcend Information TS32M~1GCF80 dimensions Word 160 Power Requirement Description

Page 56

TS32M~1GCF80

80X CompactFlash Card

 

 

 

If set to 1, indicates that the security count has expired and Security Unlock and Security Erase Unit are command aborted until a power-on reset or hard reset.

Bit 3: Freeze

If set to 1, indicates that the security is Frozen. Bit 2: Lock

If set to 1, indicates that the security is locked. Bit 1: Enable/Disable

If set to 1, indicates that the security is enabled. If set to 0, indicates that the security is disabled. Bit 0: Capability

If set to 1, indicates that CompactFlash Storage Card supports security mode feature set.

If set to 0, indicates that CompactFlash Storage Card does not support security mode feature set.

￿Word 160: Power Requirement Description

This word is required for CompactFlash Storage Cards that support power mode 1.

Bit 15: VLD

If set to 1, indicates that this word contains a valid power requirement description.

If set to 0, indicates that this word does not contain a power requirement description. Bit 14: RSV

This bit is reserved and shall be 0. Bit 13: -XP

If set to 1, indicates that the CompactFlash Storage Card does not have Power Level 1 commands. If set to 0, indicates that the CompactFlash Storage Card has Power Level 1 commands

Bit 12: -XE

If set to 1, indicates that Power Level 1 commands are disabled. If set to 0, indicates that Power Level 1 commands are enabled. Bit 0-11: Maximum current

This field contains the CompactFlash Storage Card’s maximum current in mA.

￿Word 162: Key Management Schemes Supported Bit 0: CPRM support

If set to 1, the device supports CPRM Scheme (Content Protection for Recordable Media) If set to 0, the device does not support CPRM.

Bits 1-15 are reserved for future additional Key Management schemes.

￿Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings

This word describes the capabilities and current settings for CFA defined advanced timing modes using the True IDE interface.

Notice! The use of True IDE PIO Modes 5 and above or of Multiword DMA Modes 3 and above impose significant restrictions on the implementation of the host:

Additional Requirements for CF Advanced Timing Modes.

There are four separate fields defined that describe support and selection of Advanced PIO timing modes and Advanced Multiword DMA timing modes. The older modes are reported in words 63 and 64.

Word 63: Multiword DMA transfer and 6.2.1.6.19: Word 64: Advanced PIO transfer modes supported.

Bits 2-0: Advanced True IDE PIO Mode Support Indicates the maximum True IDE PIO mode supported by the card.

Value

Maximum PIO mode timing selected

0

Specified in word 64

1

PIO Mode 5

2

PIO Mode 6

3-7

Reserved

Bits 5-3: Advanced True IDE Multiword DMA Mode Support Indicates the maximum True IDE Multiword DMA

Transcend Information Inc.

56

V1.1

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Placement Feature DimensionsDescription 80X CompactFlash CardOrdering Information CHS and CapacityCompactflash Card Specification Block Diagram PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Electrical Interface Pin Assignment and Pin TypeV1.1 Signal Description Signal Name Dir Pin DescriptionCsel V1.1 Iord REG True IDE Mode As Iordy Electrical Specification Input Leakage CurrentInput Characteristics CompactFlash interface I/O at Parameter Symbol Min Max Unit RemarkParameter Min Max UnitOutput Drive Type Output Drive Characteristics Signal Interface Signal Card HostTS32M~1GCF8080X CompactFlash Card 150 μ a high state per socketFigure Attribute Memory Read Timing Diagram Attribute Memory Read TimingConfiguration Register Attribute Memory Write Timing Min Max Symbol Common Memory Read Timing SpecificationCycle Time Mode 250 ns 120 ns 100 ns 80 ns Common Memory Write Timing Specification Min SymbolI/O Input Read Timing Specification 80X CompactFlash Card10 I/O Output Write Timing Specification Cycle Time Mode 255 ns 120 ns 100 ns 80 nsTrue IDE PIO Mode Read/Write Timing Specification ModeV1.1 True IDE Multiword DMA Mode Read/Write Timing Specification Card Configuration Multiple Function CompactFlash Storage CardsCE2 CE1 A10 A8-A4CE2 CE1 A10 D15-D8 D7-D0 Function ModeAttribute Memory Function Table CompactFlash Storage Card Configurations Configuration Option RegisterBase + 00h in Attribute MemoryPin Replacement Register Base + 04h in Attribute Memory Table Pin Replacement Changed Bit/Mask Bit ValuesSocket and Copy Register Base + 06h in Attribute Memory I/O Transfer FunctionTrue IDE Mode I/O Transfer Function Table Pcmcia Mode I/O FunctionCommon Memory Transfer Function Function CodeV1.1 Table I/O Configurations CF-ATA Drive Register Set Definition and ProtocolI/O Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingMemory Mapped Addressing Data Register Address 1F0h170hOffset 0,8,9 True IDE Mode AddressingCF-ATA Registers Error Register Address 1F1h171h Offset 1, 0Dh Read Only Table Data Register AccessFeature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetDevice Control Register Address 3F6h376h Offset Eh Figure Status & Alternate Status RegisterCard Drive Address Register Address 3F7h377h Offset Fh Figure Device Control RegisterCF-ATA Command Description CF-ATA Command Set LBADefinitions Check Power Mode 98h or E5h Execute Drive Diagnostic 90hBit Command Cyl High Cyl Low Sec Num Sec Cnt FeatureErase Sectors C0h Format Track 50hDrive Head LBA Cyl High Sec Num LBA Sec CntBytes Word Default Total Data Field Type InformationIdentify Device Ech Total Data Field Type Information Word 0 General Configuration Word 1 Default Number of CylindersWord 3 Default Number of Heads Word 6 Default Number of Sectors per TrackWord 49 Capabilities Bit 13 Standby Timer PIO Data Transfer Cycle Timing ModeMultiple Sector Setting Total Sectors Addressable in LBA ModeMultiword DMA transfer Word 64 Advanced PIO transfer modes supportedWord 65 Minimum Multiword DMA transfer cycle time Recommended Multiword DMA transfer cycle timeWord 68 Minimum PIO transfer cycle time with Iordy Words 82-84 Features/command sets supportedWords 85-87 Features/command sets enabled Word 128 Security Status Bit 8 Security Level Word 91 Advanced power management level valueWord 89 Time required for Security erase unit completion Additional Requirements for CF Advanced Timing Modes Word 160 Power Requirement DescriptionValue Maximum PIO mode timing selected Value Maximum Multiword DMA timing mode supported Value Current PIO timing mode selectedValue Current Multiword DMA timing mode selected Value Maximum Pcmcia IO timing mode SupportedDrive Cyl High Cyl Low Sec Num Sec Cnt Feature Idle 97h or E3hIdle Immediate 95h or E1h Initialize Drive Parameters 91hRead Buffer E4h Read DMA C8hRead Multiple C4h Read Sectors 20h or 21h Read Verify Sectors 40h or 41hRecalibrate 1Xh Request Sense 03hTable Extended Error Codes Seek 7XhSet Features EFh Table Feature SupportedSet Multiple Mode C6h Set Sleep Mode- 99h or E6h Standby 96h or E2hTableTranslate Sector Information Standby Immediate 94h or E0hTranslate Sector 87h Write DMA CAh Wear Level F5hWrite Buffer E8h Write Multiple Command C5h Write Multiple without Erase CDh Write Sectors 30h or 31hWrite Sectors without Erase 38h Write Verify 3Ch80X CompactFlash Card Error Posting BBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERRAddress Data Description of Contents CIS function CIS DescriptionAddress Data 5 4 Description of Contents CIS function Cistplconfig V1.1 MS IR IO RO a Address Data 5 4 3 2 1 Description of Contents CIS function Irqn LS AS NR RO a T
Top Page Image Contents