Transcend Information TS32M~1GCF80 dimensions Table CompactFlash Storage Card Configurations

Page 30

TS32M~1GCF80

80X CompactFlash Card

 

 

 

4.3 Configuration Option Register(Base + 00h in Attribute Memory)

The Configuration Option Register is used to configure the cards interface, address decoding and interrupt and to issue a soft reset to the CompactFlash Storage Card.

SRESET - Soft Reset: setting this bit to one (1), waiting the minimum reset width time and returning to zero (0) places the CompactFlash Storage Card in the Reset state. Setting this bit to one (1) is equivalent to assertion of the +RESET signal except that the SRESET bit is not cleared. Returning this bit to zero (0) leaves the CompactFlash Storage Card in the same un-configured, Reset state as following power-up and hardware reset. This bit is set to zero (0) by power-up and hardware reset. For CompactFlash Storage Cards, using the PCMCIA Soft Reset is considered a hard Reset by the ATA Commands. Contrast with Soft Reset in the Device Control Register.

LevlREQ: this bit is set to one (1) when Level Mode Interrupt is selected, and zero (0) when Pulse Mode is selected. Set to zero (0) by Reset.

Conf5 - Conf0 - Configuration Index: set to zero (0) by reset. It is used to select operation mode of the CompactFlash Storage Card as shown below.

Note: Conf5 and Conf4 are reserved for CompactFlash Storage cards and shall be written as zero (0).

Table: CompactFlash Storage Card Configurations

4.4 Card Configuration and Status Register (Base + 02h in Attribute Memory)

The Card Configuration and Status Register contains information about the Card’s condition.

Changed: indicates that one or both of the Pin Replacement register CReady, or CWProt bits are set to one (1). When the Changed bit is set, -STSCHG Pin 46 is held low if the SigChg bit is a One (1) and the CompactFlash Storage Card is configured for the I/O interface.

SigChg: this bit is set and reset by the host to enable and disable a state-change “signal” from the Status Register, the Changed bit controls pin 46, the Changed Status signal. If no state change signal is desired, this bit is set to zero

(0)and pin 46 (-STSCHG) signal is then held high while the CompactFlash Storage Card is configured for I/O.

IOis8: the host sets this bit to a one (1) if the CompactFlash Storage Card is to be configured in an 8 bit I/O Mode. The

Transcend Information Inc.

30

V1.1

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Description Placement FeatureDimensions 80X CompactFlash CardOrdering Information CHS and CapacityCompactflash Card Specification Block Diagram PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Electrical Interface Pin Assignment and Pin TypeV1.1 Signal Description Signal Name Dir Pin DescriptionCsel V1.1 Iord REG True IDE Mode As Iordy Electrical Specification Input Leakage CurrentInput Characteristics CompactFlash interface I/O at Parameter Symbol Min Max Unit RemarkParameter Min Max UnitOutput Drive Type Output Drive Characteristics Signal Interface Signal Card HostTS32M~1GCF8080X CompactFlash Card 150 μ a high state per socketFigure Attribute Memory Read Timing Diagram Attribute Memory Read TimingConfiguration Register Attribute Memory Write Timing Common Memory Read Timing Specification Cycle Time Mode 250 ns 120 ns 100 ns 80 nsMin Max Symbol Common Memory Write Timing Specification Min SymbolI/O Input Read Timing Specification 80X CompactFlash Card10 I/O Output Write Timing Specification Cycle Time Mode 255 ns 120 ns 100 ns 80 nsTrue IDE PIO Mode Read/Write Timing Specification ModeV1.1 True IDE Multiword DMA Mode Read/Write Timing Specification CE2 CE1 Card ConfigurationMultiple Function CompactFlash Storage Cards A10 A8-A4Function Mode Attribute Memory FunctionCE2 CE1 A10 D15-D8 D7-D0 Table CompactFlash Storage Card Configurations Configuration Option RegisterBase + 00h in Attribute MemoryPin Replacement Register Base + 04h in Attribute Memory Table Pin Replacement Changed Bit/Mask Bit ValuesSocket and Copy Register Base + 06h in Attribute Memory I/O Transfer FunctionCommon Memory Transfer Function True IDE Mode I/O Transfer FunctionTable Pcmcia Mode I/O Function Function CodeV1.1 Table I/O Configurations CF-ATA Drive Register Set Definition and ProtocolI/O Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingMemory Mapped Addressing True IDE Mode Addressing CF-ATA RegistersData Register Address 1F0h170hOffset 0,8,9 Error Register Address 1F1h171h Offset 1, 0Dh Read Only Table Data Register AccessSector Number LBA 7-0 Register Address 1F3h173h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetDevice Control Register Address 3F6h376h Offset Eh Figure Status & Alternate Status RegisterCard Drive Address Register Address 3F7h377h Offset Fh Figure Device Control RegisterCF-ATA Command Description CF-ATA Command Set LBADefinitions Bit Command Check Power Mode 98h or E5hExecute Drive Diagnostic 90h Cyl High Cyl Low Sec Num Sec Cnt FeatureDrive Head LBA Cyl High Erase Sectors C0hFormat Track 50h Sec Num LBA Sec CntWord Default Total Data Field Type Information Identify Device EchBytes Total Data Field Type Information Word 3 Default Number of Heads Word 0 General ConfigurationWord 1 Default Number of Cylinders Word 6 Default Number of Sectors per TrackMultiple Sector Setting Word 49 Capabilities Bit 13 Standby TimerPIO Data Transfer Cycle Timing Mode Total Sectors Addressable in LBA ModeWord 65 Minimum Multiword DMA transfer cycle time Multiword DMA transferWord 64 Advanced PIO transfer modes supported Recommended Multiword DMA transfer cycle timeWords 82-84 Features/command sets supported Words 85-87 Features/command sets enabledWord 68 Minimum PIO transfer cycle time with Iordy Word 91 Advanced power management level value Word 89 Time required for Security erase unit completionWord 128 Security Status Bit 8 Security Level Word 160 Power Requirement Description Value Maximum PIO mode timing selectedAdditional Requirements for CF Advanced Timing Modes Value Current Multiword DMA timing mode selected Value Maximum Multiword DMA timing mode supportedValue Current PIO timing mode selected Value Maximum Pcmcia IO timing mode SupportedIdle Immediate 95h or E1h Drive Cyl High Cyl Low Sec Num Sec Cnt FeatureIdle 97h or E3h Initialize Drive Parameters 91hRead Buffer E4h Read DMA C8hRead Multiple C4h Read Sectors 20h or 21h Read Verify Sectors 40h or 41hRecalibrate 1Xh Request Sense 03hTable Extended Error Codes Seek 7XhSet Features EFh Table Feature SupportedSet Multiple Mode C6h Set Sleep Mode- 99h or E6h Standby 96h or E2hStandby Immediate 94h or E0h Translate Sector 87hTableTranslate Sector Information Wear Level F5h Write Buffer E8hWrite DMA CAh Write Multiple Command C5h Write Multiple without Erase CDh Write Sectors 30h or 31hWrite Sectors without Erase 38h Write Verify 3Ch80X CompactFlash Card Error Posting BBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERRAddress Data Description of Contents CIS function CIS DescriptionAddress Data 5 4 Description of Contents CIS function Cistplconfig V1.1 MS IR IO RO a Address Data 5 4 3 2 1 Description of Contents CIS function Irqn LS AS NR RO a T
Top Page Image Contents