Transcend Information TS32M~1GCF80 dimensions Set Features EFh, Table Feature Supported

Page 64

TS32M~1GCF80		80X CompactFlash Card

5.6.18 Set Features – EFh

This command is used by the host to establish or select certain features. If any subcommand input value is not supported or is invalid, the Compact Flash Storage Card shall return command aborted. Table: Feature Supported defines all features that are supported.

Table: Feature Supported

Transcend Information Inc.

64

V1.1

Image 64

Contents Placement Feature DimensionsDescription 80X CompactFlash CardOrdering Information CHS and CapacityCompactflash Card Specification Block Diagram PC Card Memory Mode PC Card I/O Mode True IDE Mode4 Electrical Interface Pin Assignment and Pin TypeV1.1 Signal Description Signal Name Dir Pin DescriptionCsel V1.1 Iord REG True IDE Mode As Iordy Electrical Specification Input Leakage CurrentInput Characteristics CompactFlash interface I/O at Parameter Symbol Min Max Unit RemarkParameter Min Max UnitOutput Drive Type Output Drive Characteristics Signal Interface Signal Card HostTS32M~1GCF8080X CompactFlash Card 150 μ a high state per socketFigure Attribute Memory Read Timing Diagram Attribute Memory Read TimingConfiguration Register Attribute Memory Write Timing Cycle Time Mode 250 ns 120 ns 100 ns 80 ns Common Memory Read Timing SpecificationMin Max Symbol Common Memory Write Timing Specification Min SymbolI/O Input Read Timing Specification 80X CompactFlash Card10 I/O Output Write Timing Specification Cycle Time Mode 255 ns 120 ns 100 ns 80 nsTrue IDE PIO Mode Read/Write Timing Specification ModeV1.1 True IDE Multiword DMA Mode Read/Write Timing Specification Card Configuration Multiple Function CompactFlash Storage CardsCE2 CE1 A10 A8-A4Attribute Memory Function Function ModeCE2 CE1 A10 D15-D8 D7-D0 Table CompactFlash Storage Card Configurations Configuration Option RegisterBase + 00h in Attribute MemoryPin Replacement Register Base + 04h in Attribute Memory Table Pin Replacement Changed Bit/Mask Bit ValuesSocket and Copy Register Base + 06h in Attribute Memory I/O Transfer FunctionTrue IDE Mode I/O Transfer Function Table Pcmcia Mode I/O FunctionCommon Memory Transfer Function Function CodeV1.1 Table I/O Configurations CF-ATA Drive Register Set Definition and ProtocolI/O Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingMemory Mapped Addressing CF-ATA Registers True IDE Mode AddressingData Register Address 1F0h170hOffset 0,8,9 Error Register Address 1F1h171h Offset 1, 0Dh Read Only Table Data Register AccessFeature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetDevice Control Register Address 3F6h376h Offset Eh Figure Status & Alternate Status RegisterCard Drive Address Register Address 3F7h377h Offset Fh Figure Device Control RegisterCF-ATA Command Description CF-ATA Command Set LBADefinitions Check Power Mode 98h or E5h Execute Drive Diagnostic 90hBit Command Cyl High Cyl Low Sec Num Sec Cnt FeatureErase Sectors C0h Format Track 50hDrive Head LBA Cyl High Sec Num LBA Sec CntIdentify Device Ech Word Default Total Data Field Type InformationBytes Total Data Field Type Information Word 0 General Configuration Word 1 Default Number of CylindersWord 3 Default Number of Heads Word 6 Default Number of Sectors per TrackWord 49 Capabilities Bit 13 Standby Timer PIO Data Transfer Cycle Timing ModeMultiple Sector Setting Total Sectors Addressable in LBA ModeMultiword DMA transfer Word 64 Advanced PIO transfer modes supportedWord 65 Minimum Multiword DMA transfer cycle time Recommended Multiword DMA transfer cycle timeWords 85-87 Features/command sets enabled Words 82-84 Features/command sets supportedWord 68 Minimum PIO transfer cycle time with Iordy Word 89 Time required for Security erase unit completion Word 91 Advanced power management level valueWord 128 Security Status Bit 8 Security Level Value Maximum PIO mode timing selected Word 160 Power Requirement DescriptionAdditional Requirements for CF Advanced Timing Modes Value Maximum Multiword DMA timing mode supported Value Current PIO timing mode selectedValue Current Multiword DMA timing mode selected Value Maximum Pcmcia IO timing mode SupportedDrive Cyl High Cyl Low Sec Num Sec Cnt Feature Idle 97h or E3hIdle Immediate 95h or E1h Initialize Drive Parameters 91hRead Buffer E4h Read DMA C8hRead Multiple C4h Read Sectors 20h or 21h Read Verify Sectors 40h or 41hRecalibrate 1Xh Request Sense 03hTable Extended Error Codes Seek 7XhSet Features EFh Table Feature SupportedSet Multiple Mode C6h Set Sleep Mode- 99h or E6h Standby 96h or E2hTranslate Sector 87h Standby Immediate 94h or E0hTableTranslate Sector Information Write Buffer E8h Wear Level F5hWrite DMA CAh Write Multiple Command C5h Write Multiple without Erase CDh Write Sectors 30h or 31hWrite Sectors without Erase 38h Write Verify 3Ch80X CompactFlash Card Error Posting BBK UNC Idnf Abrt Amnf Drdy DWF DSC Corr ERRAddress Data Description of Contents CIS function CIS DescriptionAddress Data 5 4 Description of Contents CIS function Cistplconfig V1.1 MS IR IO RO a Address Data 5 4 3 2 1 Description of Contents CIS function Irqn LS AS NR RO a T