Agilent Technologies AGILENT MODELS 6023A and 6028A Schematic Notes, Schematic Diagram Notes 103

Page 103

SCHEMATIC NOTES

1.ALL RESISTORS ARE IN OHMS, ± 5%, 1/4W, UNLESS OTHERWISE INDICATED.

2.ALL CAPACITORS ARE IN MICROFARADS, UNLESS OTHERWISE INDICATED.

3.WHITE SILKSCREENED DOTS ON P. C. BOARDS INDICATE ONE OF THE FOLLOWING:

A.PIN 1 OF AN I. C. (EXCEPT FOR U18 SEE NOTE 4 ).

B.POSITIVE END OF A POLARIZED CAPACITOR.

C.CATHODE OF A DIODE OR THE EMITTER OF A TRANSISTOR.

4.PIN LOCATIONS FOR SEMICONDUCTORS ARE SHOWN BELOW:

5.ON VOLTAGE REGULATOR DEVICES,

REF SUPPLY BIAS FOR REGULATORS INTERNAL REFERENCE. REF = OUTPUT FROM REGULATORS INTERNAL REFERENCE. BOOST OUTPUT = CONTROL FOR EXTERNAL PASS TRANSISTOR CS = CURRENT SENSE

CL = CURRENT LIMIT

INV = INVERTING INPUT TO REGULATORS ERROR AMPLIFIER

NI = NON-INVERTING INPUT TO REGULATORS ERROR AMPLIFIER. COMP = FREQUENCY COMPENSATION

Schematic Diagram Notes

103

Image 103
Contents Autoranging Certification Safety Summary Printing History Safety Symbol DefinitionsTable of Contents Replaceable Parts Scope TroubleshootingCircuit Diagrams Safety ConsiderationsItem Description Manual RevisionsOperation Verification Tests Calibration ProcedureIntroduction Test Equipment RequiredTest Equipment Required Type Required Characteristics USE Recommended Model1KVA Initial SetupMON Calibration ProcedureIout VoutMeasurement Techniques Performance TestsCR7 Constant Voltage CV Tests Current-Monitoring Resistor SetupBasic Test Setup RMS Measurement Test Setup, CV Pard Test Peak-To-Peak Measurement Test Setup, CV Pard Test KHz Noise, CV Peak-to-Peak Pard 6023A 6028ALoad Transient Recovery Waveform Constant Current CC Tests CC Pard Test Setup Initial Troubleshooting Procedures TroubleshootingWAVEFORM/CONDITIONS Source Control Board Test Connector, A2J7PIN no Signal Name VdcElectrostatic Protection Repair and ReplacementA2 Control Board Removal A1 Main Board Removal A4 Power Mesh Board RemovalOverall Troubleshooting Procedure A3 Front-Panel Board RemovalMeasurement Using the TablesSetup NodeMain Troubleshooting Setup Main Troubleshooting SetupModified Mains Cord Set For Troubleshooting Front-Panel Troubleshooting Troubleshooting No-Output FailuresA2J7-26 A2J7-25 PWM-ON PWM-OFF Defective Check Functional CircuitsBoard Node + Measurement Source Troubleshooting Bias SuppliesSymptoms Defective Circuit Check Components Symptoms Defective Check Functional Circuits BoardMeasurement Source Node +Node + N0DE Setup Measurement Power Section BlocksTroubleshooting AC-Turn-on Circuits Setup Measurement SourceRelay Enable Troubleshooting PWM & ClockPower Limit PWM-OFF Troubleshooting DC-To-DC Converter+ OUT PWM-ONTroubleshooting CC Circuit Troubleshooting CV CircuitTroubleshooting OVP Circuit Troubleshooting Down ProgrammerA4U4OUT Waveforms SET Voltage Vdc Node + Page Block Diagram Overview Autoranging PowerBlock Diagram Simplified Schematic Simplified Schematic Down Programmer DC-to-DC ConverterConstant-Voltage CV Circuit Pfet Control Signals Timing DiagramControl-Voltage Comparator Power-Limit ComparatorConstant-Current CC Circuit Overvoltage Protection OVP CircuitAC-Surge Dropout Detector Initial-Ramp CircuitPulse-Width Modulator PWM Bias Voltage DetectorDisplay Circuits Second-Delay CircuitPage Reference Designators Replaceable PartsDescription Abbreviations Ordering InformationCR3 Electrical PartsCR1 CR2XA2P2 XA2P1Mechanical Parts Control Board Assembly CR3 Page Page Page VR4 VR3VR5 DS1 CR5DS5 VR1 IC A/D Cmos 3-1/2 DGTVR2 Pfet NPN SIChassis Electrical TS1A4 Board Mechanical Parts A1TB1A2 Board Mechanical Parts A3 Board Mechanical PartsOption 240 240V Operation Option 220 220V OperationComponent Location and Circuit Diagrams Schematic Diagram Notes Pin locations for other semi-conductors are shown below Top View, Top Covers Removed Main Board A1 Component Location Control Board A2 Component Location Front-Panel Board A3 Component Location Power Mesh Board A4 Component Location Page Page General Information SpecificationsOption 002 Hardware Status Indicators Table A-1. Specifications, Option Remote ProgrammingInput Compliance Voltage ± Current Programming Enable Output Impedance 10.2 k ohm ± 5% Temperature CoefficientOn State logic low Remote Trip and Remote Reset TimingPower-on Preset Maximum Output Voltage logic high +Pard Typical Table A-1. Specifications, Option Pulse TimingBias Supplies DC Output Ratings 25C ± Short Circuit Output CurrentConnector Assembly Procedure InstallationOperation Figure A-1. Mating Connector AssemblyLocal/Remote Programming Resistance Voltage or Current Figure A-4. Calculating Value of Series Dropping Resistor Remote Resistance ProgrammingFigure A-5. Remote Resistance Programming Remote Monitoring Remote Control Status IndicatorsOvervoltage Remote ResetFigure A-8. Remote Control Power-On PresetMultiple Supply System Shutdown AC Dropout Buffer CircuitBias Supplies MaintenanceTroubleshooting Current Programming Troubleshooting Resistance and Voltage ProgrammingFigure A-11. Troubleshooting Current Programming of CV Mode Figure A-13. Troubleshooting Status Indicators Page REF. Desig Model no Description Table A-3. Replacement Parts100 101 VR9Definitions Indicator and Qualifier SymbolsOLD Symbol NEW Symbol Logic Symbols and Definitions 102Schematic Diagram Notes 103 Schematic NotesFigure A-15. Option 002 Board, Component Location 104 Schematic NotesFigure A-16. Option 002 Board, Schematic Diagram 105 Page Model 6028A Model 6023A107 108 From