Agilent Technologies AGILENT MODELS 6023A and 6028A 6023A 6028A, KHz Noise, CV Peak-to-Peak Pard

Page 19

6023A

6028A

Figure 2-6. 20KHz Noise, CV Peak-to-Peak PARD

Load Transient Recovery Time. Specified for CV operation only; load transient recovery time is the time for the output voltage to return to within a specified band around its set voltage following a step change in load.

Proceed as follows:

a.Connect the test equipment as shown in Figure 2-3. Operate the load in constant-current mode and set for minimum current.

b.Turn the unit's power on, and turn up current setting to full output.

c.Turn up output voltage to: 6.70Vdc (6023A) 20.0Vdc (6028A)

as read on the digital voltmeter.

d.Set the load to vary the load current between:

27 and 30Adc (6023A)

9 and 10Adc (6028A) at a 30Hz rate.

e.Set the oscilloscope for ac coupling, internal sync and lock on either the positive or negative load transient.

f.Adjust the oscilloscope to display transients as in Figure 2-7.

g.Check that the pulse width of the transient pulse is no more than: 50mV (6023A)

75mV (6028A)

19

Image 19

Contents Autoranging Certification Safety Summary Printing History Safety Symbol DefinitionsTable of Contents Replaceable Parts Scope TroubleshootingCircuit Diagrams Safety ConsiderationsItem Description Manual RevisionsOperation Verification Tests Calibration ProcedureIntroduction Test Equipment RequiredTest Equipment Required Type Required Characteristics USE Recommended Model1KVA Initial SetupMON Calibration ProcedureIout VoutMeasurement Techniques Performance TestsCR7 Constant Voltage CV Tests Current-Monitoring Resistor SetupBasic Test Setup RMS Measurement Test Setup, CV Pard Test Peak-To-Peak Measurement Test Setup, CV Pard Test KHz Noise, CV Peak-to-Peak Pard 6023A 6028ALoad Transient Recovery Waveform Constant Current CC Tests CC Pard Test Setup Initial Troubleshooting Procedures TroubleshootingWAVEFORM/CONDITIONS Source Control Board Test Connector, A2J7PIN no Signal Name VdcElectrostatic Protection Repair and ReplacementA2 Control Board Removal A1 Main Board Removal A4 Power Mesh Board RemovalOverall Troubleshooting Procedure A3 Front-Panel Board RemovalMeasurement Using the TablesSetup NodeMain Troubleshooting Setup Main Troubleshooting SetupModified Mains Cord Set For Troubleshooting Front-Panel Troubleshooting Troubleshooting No-Output FailuresA2J7-26 A2J7-25 PWM-ON PWM-OFF Defective Check Functional CircuitsBoard Node + Measurement Source Troubleshooting Bias SuppliesSymptoms Defective Circuit Check Components Symptoms Defective Check Functional Circuits BoardMeasurement Source Node +Node + N0DE Setup Measurement Power Section BlocksTroubleshooting AC-Turn-on Circuits Setup Measurement SourceRelay Enable Troubleshooting PWM & ClockPower Limit PWM-OFF Troubleshooting DC-To-DC Converter+ OUT PWM-ONTroubleshooting CC Circuit Troubleshooting CV CircuitTroubleshooting OVP Circuit Troubleshooting Down ProgrammerA4U4OUT Waveforms SET Voltage Vdc Node + Page Block Diagram Overview Autoranging PowerBlock Diagram Simplified Schematic Simplified Schematic Down Programmer DC-to-DC ConverterConstant-Voltage CV Circuit Pfet Control Signals Timing DiagramControl-Voltage Comparator Power-Limit ComparatorConstant-Current CC Circuit Overvoltage Protection OVP CircuitAC-Surge Dropout Detector Initial-Ramp CircuitPulse-Width Modulator PWM Bias Voltage DetectorDisplay Circuits Second-Delay CircuitPage Reference Designators Replaceable PartsDescription Abbreviations Ordering InformationCR3 Electrical PartsCR1 CR2XA2P2 XA2P1Mechanical Parts Control Board Assembly CR3 Page Page Page VR4 VR3VR5 DS1 CR5DS5 VR1 IC A/D Cmos 3-1/2 DGTVR2 Pfet NPN SIChassis Electrical TS1A4 Board Mechanical Parts A1TB1A2 Board Mechanical Parts A3 Board Mechanical PartsOption 240 240V Operation Option 220 220V OperationComponent Location and Circuit Diagrams Schematic Diagram Notes Pin locations for other semi-conductors are shown below Top View, Top Covers Removed Main Board A1 Component Location Control Board A2 Component Location Front-Panel Board A3 Component Location Power Mesh Board A4 Component Location Page Page General Information SpecificationsOption 002 Hardware Status Indicators Table A-1. Specifications, Option Remote ProgrammingInput Compliance Voltage ± Current Programming Enable Output Impedance 10.2 k ohm ± 5% Temperature CoefficientOn State logic low Remote Trip and Remote Reset TimingPower-on Preset Maximum Output Voltage logic high +Pard Typical Table A-1. Specifications, Option Pulse TimingBias Supplies DC Output Ratings 25C ± Short Circuit Output CurrentConnector Assembly Procedure InstallationOperation Figure A-1. Mating Connector AssemblyLocal/Remote Programming Resistance Voltage or Current Figure A-4. Calculating Value of Series Dropping Resistor Remote Resistance ProgrammingFigure A-5. Remote Resistance Programming Remote Monitoring Remote Control Status IndicatorsOvervoltage Remote ResetFigure A-8. Remote Control Power-On PresetMultiple Supply System Shutdown AC Dropout Buffer CircuitBias Supplies MaintenanceTroubleshooting Current Programming Troubleshooting Resistance and Voltage ProgrammingFigure A-11. Troubleshooting Current Programming of CV Mode Figure A-13. Troubleshooting Status Indicators Page REF. Desig Model no Description Table A-3. Replacement Parts100 101 VR9Definitions Indicator and Qualifier SymbolsOLD Symbol NEW Symbol Logic Symbols and Definitions 102Schematic Diagram Notes 103 Schematic NotesFigure A-15. Option 002 Board, Component Location 104 Schematic NotesFigure A-16. Option 002 Board, Schematic Diagram 105 Page Model 6028A Model 6023A107 108 From