Agilent Technologies AGILENT MODELS 6023A and 6028A service manual

Page 97

Figure A-13. Troubleshooting Status Indicators

To check CV Mode proceed as follows:

a.Using test set-up, Figure A-13, connect to end of 2KΩ resistor to J3-36.

b.Turn on power supply.

c.Using "Display Setting'' set voltage and current or power supply for 1 volt and 1 amp.

d.DVM should read between 0 and 0.4Vdc.

e.Turn off power supply and short to output terminals.

f.Turn on power supply.

g.DVM should read approximately 5Vdc.

To check CC Mode proceed as follows:

a.Using test set-up, Figure A-13, connect top end of 2KΩ resistor to J3-35.

b.Turn on power supply.

c.Using "Display Settings'' set voltage for 1 volt and current for 1 Amp.

d.DVM should read = 5Vdc.

e.Turn off power supply and short the output terminals.

f.Turn on power supply.

g.DVM should read between 0 and 0.4Vdc.

To check OVERVOLTAGE proceed as follows:

a.Using test set-up, Figure A-13, connect top end of 2KΩ resistor to J3-17.

b.Turn "OVP Adjust" fully clockwise and voltage control fully counter clockwise.

c.Open power supply output terminals and turn on power.

d.DVM should read approximately 5Vdc.

e.Press "Display Settings" and increase voltage control for 15Vdc output.

f.Turn "OVP Adjust'' counterclockwise until supply goes into overvoltage.

g.DVM should read between 0 and 0.4Vdc.

h.Turn "OVP Adjust" fully clockwise and turn off input power for 5 seconds.

i.Turn on input power and DVM should read approximately 5Vdc.

To check OUTPUT UNREGULATED proceed as follows:

a.Using test set-up, Figure A-13, connect to end of 2KΩ to J3-18.

b.Connect output terminals of power supply to an electronic load capable of exceed the power supplies output power rating by 50%.

97

Image 97

Contents Autoranging Certification Safety Summary Printing History Safety Symbol DefinitionsTable of Contents Replaceable Parts Circuit Diagrams TroubleshootingSafety Considerations ScopeItem Description Manual RevisionsIntroduction Calibration ProcedureTest Equipment Required Operation Verification TestsTest Equipment Required Type Required Characteristics USE Recommended Model1KVA Initial SetupMON Calibration ProcedureIout VoutMeasurement Techniques Performance TestsCR7 Constant Voltage CV Tests Current-Monitoring Resistor SetupBasic Test Setup RMS Measurement Test Setup, CV Pard Test Peak-To-Peak Measurement Test Setup, CV Pard Test KHz Noise, CV Peak-to-Peak Pard 6023A 6028ALoad Transient Recovery Waveform Constant Current CC Tests CC Pard Test Setup Initial Troubleshooting Procedures TroubleshootingPIN no Signal Name Control Board Test Connector, A2J7Vdc WAVEFORM/CONDITIONS SourceElectrostatic Protection Repair and ReplacementA2 Control Board Removal Overall Troubleshooting Procedure A4 Power Mesh Board RemovalA3 Front-Panel Board Removal A1 Main Board RemovalSetup Using the TablesNode MeasurementMain Troubleshooting Setup Main Troubleshooting SetupModified Mains Cord Set For Troubleshooting Front-Panel Troubleshooting Troubleshooting No-Output FailuresA2J7-26 A2J7-25 PWM-ON PWM-OFF Defective Check Functional CircuitsBoard Symptoms Defective Circuit Check Components Troubleshooting Bias SuppliesSymptoms Defective Check Functional Circuits Board Node + Measurement SourceMeasurement Source Node +Node + N0DE Troubleshooting AC-Turn-on Circuits Power Section BlocksSetup Measurement Source Setup MeasurementRelay Enable Troubleshooting PWM & ClockPower Limit + OUT Troubleshooting DC-To-DC ConverterPWM-ON PWM-OFFTroubleshooting CC Circuit Troubleshooting CV CircuitTroubleshooting OVP Circuit Troubleshooting Down ProgrammerA4U4OUT Waveforms SET Voltage Vdc Node + Page Block Diagram Overview Autoranging PowerBlock Diagram Simplified Schematic Simplified Schematic Down Programmer DC-to-DC ConverterConstant-Voltage CV Circuit Pfet Control Signals Timing DiagramConstant-Current CC Circuit Power-Limit ComparatorOvervoltage Protection OVP Circuit Control-Voltage ComparatorPulse-Width Modulator PWM Initial-Ramp CircuitBias Voltage Detector AC-Surge Dropout DetectorDisplay Circuits Second-Delay CircuitPage Reference Designators Replaceable PartsDescription Abbreviations Ordering InformationCR1 Electrical PartsCR2 CR3XA2P2 XA2P1Mechanical Parts Control Board Assembly CR3 Page Page Page VR4 VR3VR5 DS1 CR5DS5 VR1 IC A/D Cmos 3-1/2 DGTVR2 Pfet NPN SIChassis Electrical TS1A2 Board Mechanical Parts A1TB1A3 Board Mechanical Parts A4 Board Mechanical PartsOption 240 240V Operation Option 220 220V OperationComponent Location and Circuit Diagrams Schematic Diagram Notes Pin locations for other semi-conductors are shown below Top View, Top Covers Removed Main Board A1 Component Location Control Board A2 Component Location Front-Panel Board A3 Component Location Power Mesh Board A4 Component Location Page Page General Information SpecificationsOption 002 Hardware Input Compliance Voltage ± Current Programming Enable Table A-1. Specifications, Option Remote ProgrammingOutput Impedance 10.2 k ohm ± 5% Temperature Coefficient Status IndicatorsPower-on Preset Remote Trip and Remote Reset TimingMaximum Output Voltage logic high + On State logic lowBias Supplies DC Output Ratings 25C ± Table A-1. Specifications, Option Pulse TimingShort Circuit Output Current Pard TypicalConnector Assembly Procedure InstallationOperation Figure A-1. Mating Connector AssemblyLocal/Remote Programming Resistance Voltage or Current Figure A-4. Calculating Value of Series Dropping Resistor Remote Resistance ProgrammingFigure A-5. Remote Resistance Programming Remote Monitoring Remote Control Status IndicatorsOvervoltage Remote ResetFigure A-8. Remote Control Power-On PresetMultiple Supply System Shutdown AC Dropout Buffer CircuitBias Supplies MaintenanceTroubleshooting Current Programming Troubleshooting Resistance and Voltage ProgrammingFigure A-11. Troubleshooting Current Programming of CV Mode Figure A-13. Troubleshooting Status Indicators Page REF. Desig Model no Description Table A-3. Replacement Parts100 101 VR9OLD Symbol NEW Symbol Indicator and Qualifier SymbolsLogic Symbols and Definitions 102 DefinitionsSchematic Diagram Notes 103 Schematic NotesFigure A-15. Option 002 Board, Component Location 104 Schematic NotesFigure A-16. Option 002 Board, Schematic Diagram 105 Page Model 6028A Model 6023A107 108 From