Epson TM-FX2180 manual Operation

Page 19

EPSON FX-2180 Service Manual

1.1.13 Safety Approvals

120 V model
Safety standards:	UL1950
	CSA C22.2 No. 950
EMI:	FCC part 15 subpart B class B
	CSA C108.8 class B
220 to 240 V model
Safety standards:	EN 60950 (TÜV, NEMKO)
EMI:	EN 55022 (CISPR pub. 22) class B
	AS/NZS 3548 class B
UPS model
Safety standards:	UL1950
	CSA C22.2 No. 950
	EN 60950 (TÜV, NEMKO)
EMI:	FCC part 15 subpart B class B
	CSA C108.8 class B
	EN 55022 (CISPR pub. 22) class B
	AS/NZS 3548 class B

1.1.14 CE Marking

220 to 240 V and UPS models
Low Voltage Directive 73/23/EEC:	EN60950
EMC Directive 89/336/EEC:	EN55022 class B
	EN61000-3-2
	EN61000-3-3

	Chapter 1 Product Description
1.1.16 Ribbon Cartridge
Type:	Fabric
Color:	Black
Ribbon life:	Approx. 12 million characters
	(draft, 10 cpi, 14 dots/character)

1.2 Operation

This section provides detailed information about the control panel buttons and LEDs, and explains the printer’s beep patterns.

1.2.1 Control Panel

The control panel contains seven non-locking pushbuttons and nine LEDs, as shown below.

Figure 1-7. Control Panel

1.2.1.1 Buttons

EN50082-1

IEC801-2

IEC801-3

IEC801-4

1.1.15 Acoustic Noise

Level:	Approx. 55 dB(A), according to ISO 7779
	pattern

WARNING

The power switch is wired in the secondary circuitry of the power supply board. Therefore, the power supply’s primary circuitry remains live even after the printer is turned off.

1-10

Image 19

Contents 659,&0$18$ FCC Compliance Statement For American Users Trademarks Precautions Preface Table of Contents Page Page Product Description Character Printable Printing Speed cps SpecificationsPrinting Specifications Print Speed and Printable ColumnsVertical Adjacent Dot Density dpi ResolutionPrinting Mode Printable AreaEnvelopes Continuous PaperRoll Paper PostcardsPaper Specifications Paper Feed SpecificationsFront Entry Rear Entry Minimum Maximum Minimum Maximum Front Entry Rear Entry Bottom Entry Min Max Software Specifications Interface SpecificationsFront Entry Bottom Entry Minimum Maximum Reliability Electrical SpecificationsPhysical Specifications Environmental ConditionsOperation Button Function LEDsLEDs Color Description Lever Position Description Error Beep PatternPaper Release Lever Positions BeeperPrinting a Self Test Turning on the Double-strike ModeSpecial Functions Paper Thickness Lever PositionsChanging Default Settings Using the Bidirectional Adjustment ModeSetting Options Consumables Consumables and OptionsPrinting a Hex Dump Clearing the EepromOperating Principles Printer Mechanism OverviewOutput Voltage Applications Power Supply CircuitPower Supply Circuit Operation Board Input Voltage Fuse F1 RatingControl Circuit Operation Control CircuitCPU IC2 Component Functions+$375 Print Head Troubleshooting InformationSensor Test Points SensorsMotors Error ConditionsSymptom Problem Description Flowchart Unit Level TroubleshootingFlowchart Abnormal Paper Feeding Abnormal Power Operation Problem Cause Checkpoint Solution Repairing the Power Supply BoardWaveform Problem Cause Checkpoint Solution Repairing the Main Board Assembly15. Waveform Repairing the Printer Mechanism Repairing the Printer MechanismFFC TOP Troubleshooting Disassembly and Assembly Tool PrecautionsDescription Specification ToolsAbbreviation Part Name Specifications for ScrewsCategory Item to Question to Answer Checkmark Service Check After RepairWhenever you repair the printer, wipe Disassembly and AssemblyRear tractor tab 1 Preparing to Disassemble the PrinterRemoving the Panel Board Assembly Removing the Panel Board AssemblyRemoving the Print Head Connecting the Print Head FFCsRemoving the HP Sensor Removing the PW Sensor AssemblyRemoving the Ribbon Mask 10. Installing the PW Sensor Assembly13. Removing the Upper Housing Assembly Removing the Upper Housing Assembly15. Removing the Platen Assembly Removing the Platen AssemblyRemoving the Platen Gear Removing the Case Open Sensor AssemblyRemoving the Printer Mechanism 18. Removing the Case Open Sensor AssemblyCN9 Connector Pins21. Removing the CR Motor Assembly Removing the CR Motor Assembly22. Removing the PF Motor Removing the PF Motor Assembly23. Removing the PG Sensor Assembly Removing the PG Sensor AssemblyRemoving the Right Frame Assembly Removing the Right Sub Frame Assembly$-867017 Disassembling the Right Frame Assembly27. Engaging the Right Frame Assembly Gears 1 29. Engaging the Tractor Clutch Cam Removing the Left Frame Assembly30. Removing the Left Frame Assembly Removing the Ribbon Drive RD AssemblyTightening torque for the two CBS screws Removing the CR Assembly34. Inserting the Timing Belt 36. Installing the Rear CR Guide Shaft Removing the Rear PE Sensor Assembly38. Removing the Front PE Sensor Assembly 39. Removing the Upper Shield Plate and Upper I/F 41. Removing the Power Supply Board Assembly Removing the Power Supply Board AssemblyAdjustments Required Adjustments Adjustment OverviewAdjustment Tools Platen Gap/Parallelism Adjustment Adjusting and Resetting the PrinterSetting the PG Adjustment Lever Adjusting the Parallelism of the Carriage Guide Shaft Bidirectional Print Alignment Bi-d AdjustmentDestination Setting Performing the Bi-d Adjustment Using the Settings DisketteBi-d Adjustment Menu Performing the Bi-d Adjustment from the Control Panel11. Pitch Lights Factory SettingsTPE level. Check that the reset value is FF TPE Level Reset17. Main Menu Adjustments Maintenance Name Quantity Availability Part Number Preventive Maintenance LubricationRef. No Lubrication Points Quantity Lubricant MaintenanceLubrication Points 1 Appendix Board Connector Function Pins Connector SummarySignal Name Function Pin Signal Name Function Table A-8. Connector Pin Assignments − CN9 Table A-13. Connector Pin Assignments − CN14 Figure A-3. C244 Main Board Component Layout Diagram 2 Circuit Board Component Layout DiagramsFigure A-4. C166 PSB Board Component Layout Diagram Circuit Board and Exploded Diagrams Page DB1 A t s in k Q 1 , D 5 Page Exploded Diagram for FX-21801 Exploded Diagram for FX-21802 Exploded Diagram for FX-21803