Epson TM-FX2180 manual Connector Pins, CN9

Page 59

EPSON FX-2180 Service Manual	Chapter 4 Disassembly and Assembly

5.Disconnect the cables from the following connectors on the main

board assembly.

printer mechanism mounting screws

			Table 4-6. Main Board Connectors

Connector		Pins			Connector		Connector		Pins		Connector
Number					Color		Number				Color

CN4		3			white		CN5		3		black
CN6		2			white		CN7		4		gray
CN8		18			gray		CN9		16		gray
CN10		4			white		CN11		5		white
CN12		4			white		CN13		4		black

Note: To disconnect the cables from CN10 and CN11, pull up the connector locks.

6. As shown in Figure 4-20, remove the four printer mechanism mounting screws securing the printer mechanism.

7. Remove the printer mechanism.

IMPORTANT

When you connect the cables to CN10 and CN11, align the red line in the cable with pin 1

Tof the connector.

The tightening torque for the four printer mechanism mounting screws is 0.78 - 0.98 Nm (10 - 12 Kgf-cm).

Adjust the bidirectional print alignment and reset the TPE level. (See Chapter 5.)

Figure 4-20. Removing the Printer Mechanism

4-14

Image 59

Contents 659,&0$18$ FCC Compliance Statement For American Users Trademarks Precautions Preface Table of Contents Page Page Product Description Character Printable Printing Speed cps SpecificationsPrinting Specifications Print Speed and Printable ColumnsVertical Adjacent Dot Density dpi ResolutionPrinting Mode Printable AreaEnvelopes Continuous PaperRoll Paper PostcardsFront Entry Rear Entry Minimum Maximum Paper Feed SpecificationsPaper Specifications Minimum Maximum Front Entry Rear Entry Bottom Entry Min Max Front Entry Bottom Entry Minimum Maximum Interface SpecificationsSoftware Specifications Reliability Electrical SpecificationsPhysical Specifications Environmental ConditionsOperation LEDs Color Description LEDsButton Function Lever Position Description Error Beep PatternPaper Release Lever Positions BeeperPrinting a Self Test Turning on the Double-strike ModeSpecial Functions Paper Thickness Lever PositionsSetting Options Using the Bidirectional Adjustment ModeChanging Default Settings Consumables Consumables and OptionsPrinting a Hex Dump Clearing the EepromOperating Principles Printer Mechanism OverviewOutput Voltage Applications Power Supply CircuitPower Supply Circuit Operation Board Input Voltage Fuse F1 RatingControl Circuit Operation Control CircuitCPU IC2 Component Functions+$375 Print Head Troubleshooting InformationSensor Test Points SensorsMotors Error ConditionsSymptom Problem Description Flowchart Unit Level TroubleshootingFlowchart Abnormal Paper Feeding Abnormal Power Operation Problem Cause Checkpoint Solution Repairing the Power Supply BoardWaveform Problem Cause Checkpoint Solution Repairing the Main Board Assembly15. Waveform Repairing the Printer Mechanism Repairing the Printer MechanismFFC TOP Troubleshooting Disassembly and Assembly Tool PrecautionsDescription Specification ToolsAbbreviation Part Name Specifications for ScrewsCategory Item to Question to Answer Checkmark Service Check After RepairWhenever you repair the printer, wipe Disassembly and AssemblyRear tractor tab 1 Preparing to Disassemble the PrinterRemoving the Panel Board Assembly Removing the Panel Board AssemblyRemoving the Print Head Connecting the Print Head FFCsRemoving the HP Sensor Removing the PW Sensor AssemblyRemoving the Ribbon Mask 10. Installing the PW Sensor Assembly13. Removing the Upper Housing Assembly Removing the Upper Housing Assembly15. Removing the Platen Assembly Removing the Platen AssemblyRemoving the Platen Gear Removing the Case Open Sensor AssemblyRemoving the Printer Mechanism 18. Removing the Case Open Sensor AssemblyCN9 Connector Pins21. Removing the CR Motor Assembly Removing the CR Motor Assembly22. Removing the PF Motor Removing the PF Motor Assembly23. Removing the PG Sensor Assembly Removing the PG Sensor AssemblyRemoving the Right Frame Assembly Removing the Right Sub Frame Assembly$-867017 Disassembling the Right Frame Assembly27. Engaging the Right Frame Assembly Gears 1 29. Engaging the Tractor Clutch Cam Removing the Left Frame Assembly30. Removing the Left Frame Assembly Removing the Ribbon Drive RD AssemblyTightening torque for the two CBS screws Removing the CR Assembly34. Inserting the Timing Belt 36. Installing the Rear CR Guide Shaft Removing the Rear PE Sensor Assembly38. Removing the Front PE Sensor Assembly 39. Removing the Upper Shield Plate and Upper I/F 41. Removing the Power Supply Board Assembly Removing the Power Supply Board AssemblyAdjustments Adjustment Tools Adjustment OverviewRequired Adjustments Platen Gap/Parallelism Adjustment Adjusting and Resetting the PrinterSetting the PG Adjustment Lever Adjusting the Parallelism of the Carriage Guide Shaft Bidirectional Print Alignment Bi-d AdjustmentDestination Setting Performing the Bi-d Adjustment Using the Settings DisketteBi-d Adjustment Menu Performing the Bi-d Adjustment from the Control Panel11. Pitch Lights Factory SettingsTPE level. Check that the reset value is FF TPE Level Reset17. Main Menu Adjustments Maintenance Name Quantity Availability Part Number Preventive Maintenance LubricationRef. No Lubrication Points Quantity Lubricant MaintenanceLubrication Points 1 Appendix Signal Name Function Connector SummaryBoard Connector Function Pins Pin Signal Name Function Table A-8. Connector Pin Assignments − CN9 Table A-13. Connector Pin Assignments − CN14 Figure A-3. C244 Main Board Component Layout Diagram 2 Circuit Board Component Layout DiagramsFigure A-4. C166 PSB Board Component Layout Diagram Circuit Board and Exploded Diagrams Page DB1 A t s in k Q 1 , D 5 Page Exploded Diagram for FX-21801 Exploded Diagram for FX-21802 Exploded Diagram for FX-21803