Toshiba B-SX600 manual Standard model, Remarks

Page 102

13. FREQUENTLY ASKED QUESTIONS (FAQ)

Q: Are there any limitations on a print or feed speed in Strip mode?

A:

When the model with the Peel-off Unit is used, a print speed needs to be reduced to 4 ips or less to ensure the steady peel-off operation. (In the printer driver, a feed speed is set to the same value as a print speed.)

A print speed needs to be further reduced to 2 or 3 ips depending on the type or size of the media. Check the peel-off operation first, then adjust a print speed if necessary.

Q:Is there any difference in acceptable media and ribbons between the standard model and the model with the Peel-off Unit?

A:

There is no difference between the standard model and the model with the Peel-off Unit in the material of the acceptable media and ribbons. However, when performing peel-off operation, the size of the available media is different.

 

 

 

Standard model

 

 

Model with Peel-off Unit

 

 

Remarks

 

 

Max. backing paper

 

 

120 mm

 

 

 

 

 

width

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. label length

 

5 mm

 

 

12 mm

 

 

 

 

 

Min. media width

 

15 mm

 

 

10 mm

 

 

 

 

 

Fanfold paper

 

Allowed

 

 

Not allowed

 

 

Media may be torn off

 

 

Perforation

 

 

 

 

 

from perforation.

 

 

 

 

 

 

 

 

 

 

 

Min. label thickness

 

0.05 mm

 

 

0.05 mm

 

 

 

 

 

Max. thickness of

 

0.1 mm

 

 

0.1 mm

 

 

Glassine paper

 

 

backing paper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Roll direction

 

Inside/outside

 

 

Inside

 

 

 

 

In addition to the above specifications, be careful of the following points when using the model with the Peel-off Unit.

The acceptable media length for the Peel-off Unit is the same as that of the standard model. However, when using a long label, prevent a peeled one from sticking to the table on which the printer is placed.

Do not use a media roll with seams. Use a label stock with seamless backing paper.

Neither fabrics nor special labels are usable. Also, using non-rectangular labels is not allowed.

13- 5

Page 101 Page 103
Image 102
Page 101 Page 103
Contents SX600 Series CE Compliance for EU only VorsichtSafety Summary Meanings of Each SymbolPrecautions Table of Contents Test Print Specifications Product Overview IntroductionAccessories CD-ROMPart Names and Functions Front ViewRear View Model with a USB interface USB Interface ConnectorAC Power Inlet Fanfold Paper Slot Ventilation SlotLAN Interface Connector Rear View Model with a LAN interfaceMedia Roll Damper Platen Media Roll Guide InteriorMedia End Sensor Reflective Media Sensor Media Holder Media Guide Print HeadUpper Unit Upper Unit Handle Ribbon Tensioner Upper Unit Unlock LeverCancel key Operation PanelMenu key Cutter Unit Cut positionPrecautions when using the Cutter Unit Peel-off Unit Part namesPrecautions when using the Peel-off Unit Supplemental RemarksPrinter Setup PrecautionsRemoving the Protective Materials Printer Setup Printer Setup Installation Location 40 CConnecting the Power Cord Example of US TypeConnecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Supply Specifications Strip mode Cut modeMedia and Ribbon Die-cut label Notched media Label with black marks Guaranteed Print Area Unacceptable Media and Ribbons When you purchase media and ribbonsStorage of Media and Ribbons Preprinted MediaMedia and Ribbon Precaution Loading the RibbonRelease button Gently squeeze the metal. plate Precautions How to Load the Media Loading the MediaLoading the Media Low Supplemental Remarks How to Load the Media for the Model with the Peel-off Unit Please read .1 How to Load the Media firstPrecautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Printing from Your Computer Print Test from Printer DriverPrinting from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Strict feed mode Media Feed ModeFixed Length feed mode Easy feed modePrinter Operation Printer Operation Tear-off Alignment Alignment is performedAlignment when Precise print mode is selected Alignment when Paper saving mode is selected Alignment when Fixed Length feed mode is selected Media CalibrationHow to perform a media calibration Printer Operation Printer Operation Operation Panel Operation PanelMessages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Error messages in the event of End of paper Display in Low Power ModePrinter Operation using the Operation Panel Operation Operational procedures→ See .4 Menu Options Menu Options InformationTitle Description TripReprint Error Page menu Clear Trip Meter menuTest print menu Low Power min ConditionsBeep Volume How to Cancel a Print Job Operation Panel How to Perform a Print Test Test PrintPrint Test Pattern Removing Jammed Media Removing Jammed Media from the Cutter UnitRemoving Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Separation Plate Cleaning the Ribbon Guide BarCleaning the Print Head Cleaning the Peel-off Unit Problems while Printing TroubleshootingProblems at Start-up of the Printer Printing does not startComputer ⇒2.4 or 2.5 Connecting the Printer to Your⇒8.5 How to Cancel a Print Job ⇒ 3.7 Unacceptable Media and Ribbons⇒ 11.3 Cleaning the Ribbon Separation Plate Blank page label is ejectedLoaded ribbon is torn or ejected with the media Print Failure An entire or a part of printout is lightPrinted text is blurred ⇒ 2.2 Installation Location Printouts have streaky smudges or fine lines⇒ 7.1 Media Feed Mode Print position gradually misaligns⇒ 7.4 Media Calibration ⇒ 8.5 How to Cancel a Print Job ⇒ Help on the Printing PreferencesProblems in the Network Model with a LAN Interface ⇒ 2.5 Connecting the Printer to Your ComputerError messages and remedial measures ⇒ 1.4.2 Precautions when using the Cutter Unit How to Load the Media⇒ 1.5.2 Precaution when using the Peel-off Unit Peeling failedImage Info.Error Error messages Possible causes Solutions Info. ErrorAction Info.Error Possible causes Solutions Bad thermal headFrequently Asked Questions FAQ How can I use the printer with the covers left open?Can I use an ink ribbon narrower than a label? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Standard model RemarksSpecifications SpecificationsPrinter Model with a USB Interface Printer Model with a LAN Interface HttpSnmp Simple Network Management Protocol Specifications Cutter Unit Power Cord When purchasing the power cordPage EO1-33085
Top Page Image Contents