Toshiba B-SX600 manual Daily Maintenance, Supplemental Remarks

Page 81

11. DAILY MAINTENANCE

Please clean the printer periodically in order to ensure the continued high performance of the printer. Particularly if the Print Head, Platen, or Media Feed Section is dirty, clear printing and proper media feeding are not ensured. Use the following procedures to clean them.

Turn the Power Switch off and unplug the Power Cord of the printer from the wall outlet before cleaning the printer or replacing parts. Failure to do this may cause an electric shock or injuries.

Do not pour water on the printer or wipe it with a damp cloth.

If water enters the printer, this may cause a fire or electric shock.

The print head becomes hot immediately after printing. Allow it to cool WARNING before performing any maintenance, or you may get burned.

Do not open or close any covers other than specified in the manual. Some of the parts inside the printer have high voltage, and may cause an electric shock or injuries.

Do not use any cleaners using thinner, benzene, or flammable gas to clean the printer. This may cause a fire.

[Supplemental Remarks]

To maintain the printer performance and high quality printing for a long period of time, clean the inside of the printer every 300 m of the printing distance, which is equivalent to one roll of standard ribbon (that is approximately 300 m long) as a guide.

Use the supplied cleaning cloth to clean the printer. Please contact your nearest authorised TOSHIBA TEC representative to place an order for the cleaning cloth.

Eliminate static electricity from your body before accessing the inside of the printer. In addition, take off your ring, bracelet, or gloves, as this may damage the Print Head.

Do not use any lubricants, as this may cause a printer failure.

Do not use any chemical agents including thinner and benzene, as this may cause the discoloration or degradation of the printer. Also, do not use any solvents, detergents, or pesticides to clean the printer, as this may cause a printer failure.

11- 1

Image 81
Contents SX600 Series Vorsicht CE Compliance for EU onlyMeanings of Each Symbol Safety SummaryPrecautions Table of Contents Test Print Specifications Introduction Product OverviewCD-ROM AccessoriesFront View Part Names and FunctionsAC Power Inlet Fanfold Paper Slot USB Interface ConnectorRear View Model with a USB interface Ventilation SlotRear View Model with a LAN interface LAN Interface ConnectorMedia End Sensor Reflective Media Sensor Media Holder InteriorMedia Roll Damper Platen Media Roll Guide Media Guide Print HeadUpper Unit Handle Ribbon Tensioner Upper Unit Unlock Lever Upper UnitCancel key Operation PanelMenu key Cut position Cutter UnitPrecautions when using the Cutter Unit Part names Peel-off UnitSupplemental Remarks Precautions when using the Peel-off UnitPrinter Setup PrecautionsRemoving the Protective Materials Printer Setup Printer Setup 40 C Installation LocationExample of US Type Connecting the Power CordConnecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Supply Specifications Strip mode Cut modeMedia and Ribbon Die-cut label Notched media Label with black marks Guaranteed Print Area Storage of Media and Ribbons When you purchase media and ribbonsUnacceptable Media and Ribbons Preprinted MediaMedia and Ribbon Loading the Ribbon PrecautionRelease button Gently squeeze the metal. plate Precautions Loading the Media How to Load the MediaLoading the Media Low Supplemental Remarks Please read .1 How to Load the Media first How to Load the Media for the Model with the Peel-off UnitPrecautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Print Test from Printer Driver Printing from Your ComputerPrinting from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Fixed Length feed mode Media Feed ModeStrict feed mode Easy feed modePrinter Operation Printer Operation Tear-off Alignment is performed AlignmentAlignment when Precise print mode is selected Alignment when Paper saving mode is selected Media Calibration Alignment when Fixed Length feed mode is selectedHow to perform a media calibration Printer Operation Printer Operation Operation Panel Operation PanelMessages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Display in Low Power Mode Error messages in the event of End of paperPrinter Operation using the Operation Panel Operation Operational procedures→ See .4 Menu Options Information Menu OptionsTrip Title DescriptionReprint Error Page menu Clear Trip Meter menuTest print menu Conditions Low Power minBeep Volume How to Cancel a Print Job Operation Panel How to Perform a Print Test Test PrintPrint Test Pattern Removing Jammed Media from the Cutter Unit Removing Jammed MediaRemoving Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Guide Bar Cleaning the Ribbon Separation PlateCleaning the Print Head Cleaning the Peel-off Unit Problems at Start-up of the Printer TroubleshootingProblems while Printing Printing does not start⇒8.5 How to Cancel a Print Job ⇒2.4 or 2.5 Connecting the Printer to YourComputer ⇒ 3.7 Unacceptable Media and Ribbons⇒ 11.3 Cleaning the Ribbon Separation Plate Blank page label is ejectedLoaded ribbon is torn or ejected with the media Print Failure An entire or a part of printout is lightPrinted text is blurred Printouts have streaky smudges or fine lines ⇒ 2.2 Installation Location⇒ 7.1 Media Feed Mode Print position gradually misaligns⇒ 7.4 Media Calibration ⇒ Help on the Printing Preferences ⇒ 8.5 How to Cancel a Print Job⇒ 2.5 Connecting the Printer to Your Computer Problems in the Network Model with a LAN InterfaceError messages and remedial measures ⇒ 1.5.2 Precaution when using the Peel-off Unit How to Load the Media⇒ 1.4.2 Precautions when using the Cutter Unit Peeling failedAction Info.Error Error messages Possible causes Solutions Info. ErrorImage Info.Error Possible causes Solutions Bad thermal headFrequently Asked Questions FAQ How can I use the printer with the covers left open?Can I use an ink ribbon narrower than a label? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Remarks Standard modelSpecifications SpecificationsPrinter Model with a USB Interface Http Printer Model with a LAN InterfaceSnmp Simple Network Management Protocol Specifications Cutter Unit When purchasing the power cord Power CordPage EO1-33085