Toshiba B-SX600 manual Precautions when using the Cutter Unit

Page 17

1. PRODUCT OVERVIEW

1.4.2 Precautions when using the Cutter Unit

The following precautions must be taken when the Cutter Unit is used.

・The thickness of the media that can be cut is between 0.08 mm and 0.26 mm. Do not cut any media that falls outside this range, as this may cause a printer failure.

・When using a label stock, be sure to cut the gaps. Cutting labels will cause the glue to stick to the cutter, which may affect the cutter quality and shorten the cutter life.

・Do not cut any materials other than paper (e.g. fabrics and films), as this may cause a printer failure.

・The cutter is a consumable. The cutting edge wears out from an extended period of use, causing the cutter to be blunt. When replacing the cutter, please contact your nearest authorised TOSHIBA TEC representative for assistance.

・When the perforated media is used, do not cut ± 1 mm around the perforation, as this may cause a paper jam in the Cutter Unit.

Cut position カット位置

ラLabelベル

Backing 台紙 paper

	mm１		カット禁止領域
	mm１		カット禁止領域
	±		where cuttingis
	±		where cuttingis
			Area allowednot

ミPerforationシン目

1- 10

Image 17

Contents SX600 Series Vorsicht CE Compliance for EU onlyMeanings of Each Symbol Safety SummaryPrecautions Table of Contents Test Print Specifications Introduction Product OverviewCD-ROM AccessoriesFront View Part Names and FunctionsAC Power Inlet Fanfold Paper Slot USB Interface ConnectorRear View Model with a USB interface Ventilation SlotRear View Model with a LAN interface LAN Interface ConnectorMedia End Sensor Reflective Media Sensor Media Holder InteriorMedia Roll Damper Platen Media Roll Guide Media Guide Print HeadUpper Unit Handle Ribbon Tensioner Upper Unit Unlock Lever Upper UnitMenu key Cancel keyOperation Panel Cut position Cutter UnitPrecautions when using the Cutter Unit Part names Peel-off UnitSupplemental Remarks Precautions when using the Peel-off UnitRemoving the Protective Materials Printer SetupPrecautions Printer Setup Printer Setup 40 C Installation LocationExample of US Type Connecting the Power CordConnecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Media and Ribbon Supply SpecificationsStrip mode Cut mode Die-cut label Notched media Label with black marks Guaranteed Print Area Storage of Media and Ribbons When you purchase media and ribbonsUnacceptable Media and Ribbons Preprinted MediaMedia and Ribbon Loading the Ribbon PrecautionRelease button Gently squeeze the metal. plate Precautions Loading the Media How to Load the MediaLoading the Media Low Supplemental Remarks Please read .1 How to Load the Media first How to Load the Media for the Model with the Peel-off UnitPrecautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Print Test from Printer Driver Printing from Your ComputerPrinting from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Fixed Length feed mode Media Feed ModeStrict feed mode Easy feed modePrinter Operation Printer Operation Tear-off Alignment is performed AlignmentAlignment when Precise print mode is selected Alignment when Paper saving mode is selected Media Calibration Alignment when Fixed Length feed mode is selectedHow to perform a media calibration Printer Operation Printer Operation Operation Panel Operation PanelMessages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Display in Low Power Mode Error messages in the event of End of paper→ See .4 Menu Options Printer Operation using the Operation PanelOperation Operational procedures Information Menu OptionsTrip Title DescriptionTest print menu Reprint Error Page menuClear Trip Meter menu Conditions Low Power minBeep Volume How to Cancel a Print Job Operation Panel Print Test Pattern How to Perform a Print TestTest Print Removing Jammed Media from the Cutter Unit Removing Jammed MediaRemoving Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Guide Bar Cleaning the Ribbon Separation PlateCleaning the Print Head Cleaning the Peel-off Unit Problems at Start-up of the Printer TroubleshootingProblems while Printing Printing does not start⇒8.5 How to Cancel a Print Job ⇒2.4 or 2.5 Connecting the Printer to YourComputer ⇒ 3.7 Unacceptable Media and RibbonsLoaded ribbon is torn or ejected with the media ⇒ 11.3 Cleaning the Ribbon Separation PlateBlank page label is ejected Printed text is blurred Print FailureAn entire or a part of printout is light Printouts have streaky smudges or fine lines ⇒ 2.2 Installation Location⇒ 7.4 Media Calibration ⇒ 7.1 Media Feed ModePrint position gradually misaligns ⇒ Help on the Printing Preferences ⇒ 8.5 How to Cancel a Print Job⇒ 2.5 Connecting the Printer to Your Computer Problems in the Network Model with a LAN InterfaceError messages and remedial measures ⇒ 1.5.2 Precaution when using the Peel-off Unit How to Load the Media⇒ 1.4.2 Precautions when using the Cutter Unit Peeling failedAction Info.Error Error messages Possible causes Solutions Info. ErrorImage Info.Error Possible causes Solutions Bad thermal headCan I use an ink ribbon narrower than a label? Frequently Asked Questions FAQHow can I use the printer with the covers left open? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Remarks Standard modelPrinter Model with a USB Interface SpecificationsSpecifications Http Printer Model with a LAN InterfaceSnmp Simple Network Management Protocol Specifications Cutter Unit When purchasing the power cord Power CordPage EO1-33085