Toshiba B-SX600 manual Tear-off, Supplemental Remarks

Page 57

7. PRINTER OPERATION

2.In Easy feed mode, a missing page or label is skipped over. When a label stock is used, printing can be performed even if a label is missing or even if there is a seam on the media. However, if 4 or more labels are missing in a row or if no labels are detected after the media is fed 300 mm or over, a media feed error will occur.

7.2 Tear-off

Tear-off is a function that feeds a printed label outside the Front Cover to allow you to check a print result or to easily remove a label manually.

It is possible to select the “enabling or disabling” of the tear-off function and specify a “tear-off time”*1. Please refer to the Help for the Printer Driver for further information regarding the tear-off settings.

*1 “Tear-off time” refers to a waiting time from the completion of printing until the tear-off is performed.

[Supplemental Remarks]

･When using the model with the Cutter Unit and both “Cut” and “No cutting action during printing” are selected in the printer driver, the tear-off is always performed. Whether to enable or disable the tear-off cannot be selected.

･When using the model with the Peel-off Unit and “Peel” is selected in the printer driver, the tear-off is always performed. Whether to enable or disable the tear-off cannot be selected.

7- 4

Image 57

Contents SX600 Series Vorsicht CE Compliance for EU onlyMeanings of Each Symbol Safety SummaryPrecautions Table of Contents Test Print Specifications Introduction Product OverviewCD-ROM AccessoriesFront View Part Names and FunctionsAC Power Inlet Fanfold Paper Slot USB Interface ConnectorRear View Model with a USB interface Ventilation SlotRear View Model with a LAN interface LAN Interface ConnectorMedia End Sensor Reflective Media Sensor Media Holder InteriorMedia Roll Damper Platen Media Roll Guide Media Guide Print HeadUpper Unit Handle Ribbon Tensioner Upper Unit Unlock Lever Upper UnitCancel key Operation PanelMenu key Cut position Cutter UnitPrecautions when using the Cutter Unit Part names Peel-off UnitSupplemental Remarks Precautions when using the Peel-off UnitPrinter Setup PrecautionsRemoving the Protective Materials Printer Setup Printer Setup 40 C Installation LocationExample of US Type Connecting the Power CordConnecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Supply Specifications Strip mode Cut modeMedia and Ribbon Die-cut label Notched media Label with black marks Guaranteed Print Area Storage of Media and Ribbons When you purchase media and ribbonsUnacceptable Media and Ribbons Preprinted MediaMedia and Ribbon Loading the Ribbon PrecautionRelease button Gently squeeze the metal. plate Precautions Loading the Media How to Load the MediaLoading the Media Low Supplemental Remarks Please read .1 How to Load the Media first How to Load the Media for the Model with the Peel-off UnitPrecautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Print Test from Printer Driver Printing from Your ComputerPrinting from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Fixed Length feed mode Media Feed ModeStrict feed mode Easy feed modePrinter Operation Printer Operation Tear-off Alignment is performed AlignmentAlignment when Precise print mode is selected Alignment when Paper saving mode is selected Media Calibration Alignment when Fixed Length feed mode is selectedHow to perform a media calibration Printer Operation Printer Operation Operation Panel Operation PanelMessages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Display in Low Power Mode Error messages in the event of End of paperPrinter Operation using the Operation Panel Operation Operational procedures→ See .4 Menu Options Information Menu OptionsTrip Title DescriptionReprint Error Page menu Clear Trip Meter menuTest print menu Conditions Low Power minBeep Volume How to Cancel a Print Job Operation Panel How to Perform a Print Test Test PrintPrint Test Pattern Removing Jammed Media from the Cutter Unit Removing Jammed MediaRemoving Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Guide Bar Cleaning the Ribbon Separation PlateCleaning the Print Head Cleaning the Peel-off Unit Problems at Start-up of the Printer TroubleshootingProblems while Printing Printing does not start⇒8.5 How to Cancel a Print Job ⇒2.4 or 2.5 Connecting the Printer to YourComputer ⇒ 3.7 Unacceptable Media and Ribbons⇒ 11.3 Cleaning the Ribbon Separation Plate Blank page label is ejectedLoaded ribbon is torn or ejected with the media Print Failure An entire or a part of printout is lightPrinted text is blurred Printouts have streaky smudges or fine lines ⇒ 2.2 Installation Location⇒ 7.1 Media Feed Mode Print position gradually misaligns⇒ 7.4 Media Calibration ⇒ Help on the Printing Preferences ⇒ 8.5 How to Cancel a Print Job⇒ 2.5 Connecting the Printer to Your Computer Problems in the Network Model with a LAN InterfaceError messages and remedial measures ⇒ 1.5.2 Precaution when using the Peel-off Unit How to Load the Media⇒ 1.4.2 Precautions when using the Cutter Unit Peeling failedAction Info.Error Error messages Possible causes Solutions Info. ErrorImage Info.Error Possible causes Solutions Bad thermal headFrequently Asked Questions FAQ How can I use the printer with the covers left open?Can I use an ink ribbon narrower than a label? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Remarks Standard modelSpecifications SpecificationsPrinter Model with a USB Interface Http Printer Model with a LAN InterfaceSnmp Simple Network Management Protocol Specifications Cutter Unit When purchasing the power cord Power CordPage EO1-33085