Toshiba B-9700-LAN-QM-R, B-SX5T, B9700LANQMR manual Revision Date Apr

Page 30

2. SUPPLY SPECIFICATIONS	EO10-33013B
	(Revision Date: Apr. 24, 2008)
	2.5 SPECIFICATION OF RFID TAG (for B-SX704-RFID-U2-EU/AU -R)

3) Roll-type RFID Supplies

When RFID supplies are to be rolled, roll hardness must be concerned.

Although it depends on the type of glue, tag, and backing paper, RFID-tag embedded labels tend to stay rolled. Especially, when they are wound outside, a media jam error may occur. Unless otherwise specified, it is recommended that the RFID-tag embedded labels be wound inside.

4) Sensor

When the transmissive sensor or reflective sensor is enabled, transmissivity or reflectivity of a label or tag may vary at an RFID-tag embedded area depending on the pattern of an antenna or other factors. In such cases, a manual threshold setting is required in the printer system mode. For details, refer to the B-SX4T/5T Key Operation Specifications (EAA-1379).

5) Cutter

When an RFID label or tag is used in cut issue mode, care must be taken not to cut the antenna or the IC chip of an RFID tag in order not to damage the cutter.

6) Static Electricity

When printing is performed in a place where humidity is low or under some specific conditions, writing data on an RFID tag may fail due to static electricity generated by a label or a ribbon.

2-14

Image 30

Contents SX4T/SX5T Series Table of Contents Printer Specifications Description of Model NumberX 4 T G S 1 0 Q Q R Front View/Rear View Appearance and Dimensions ApproximateDimensions Approximate Operation PanelBasic Specifications JAN8, EAN8, JAN13, EAN13, UPC-A, UPC-EMagnification of bar code Outline Electronics Specifications Specification of the MAIN4 PC Board Receive data line 1MB COM1 TCP/IP Home Position Strip Sensor Tr Print Head Print Head Media SX4TLabel Non Print Area Ribbon Care and Handling of the Media and Ribbon General Description Available Rfid TagLocation of Rfid Tag 40 mm + 5mm Media feeding direction Poor printing may occur in this area due to bump Improvement of Writing Accuracy Specification of Rfid TAG for B-SX704-RFID-U2-EU/AU-R 35 mm ±3 mm Short-pitch Tag Revision Date Apr Print quality on bumps is not guaranteed Print Position Accuracy Improvement of Writing Accuracy Specification of Rfid TAG for B-SX704-RFID-U2-US-R 35 mm ±3 mm Supply Specifications Rafsec Short Dipole2 Tag Supply Specifications Print quality on bumps is not guaranteed Print Position Accuracy Improvement of Writing Accuracy Specification of Rfid TAG for B-SX704-RFID-U2-CN-R 38 mm ±3 mm Short-pitch Tag Print quality on bumps is not guaranteed Print Position Accuracy Improvement of Writing Accuracy Optional KIT Strip Module B-9904-H-QM/QM-R option for the B-SX4T Pcmcia Interface Board B-9700-PCM-QM/QM-R BUILT-IN LAN Interface Board B-9700-LAN-QM/QM-RUSB Interface Board B-9700-USB-QM/QM-R Specification Rfid Module B-9704-RFID-U1-US/U1-EU/U1-EU-R/H1-QM/H1-QM-R10RFID Module B-SX704-RFID-U2-EU/AU/US/CN-R Applicable modelDSB-ASK Wireless LAN Board B-9700-WLAN-QM-R „ Hardware Specification„ Country code Country Code Table„ MAC address „ LED „ Precautions „ Handling Precautions for B-9700-WLAN-QM„ Certification