Toshiba B-SX5T, B-9700-LAN-QM-R, B9700LANQMR manual Print Position Accuracy

Page 46

2. SUPPLY SPECIFICATIONS

EO10-33013B

 

(Revision Date: May 22, 2009)

 

2.7 SPECIFICATION OF RFID TAG (for B-SX704-RFID-U2-CN -R)

 

 

10) Caution for minimum label pitch length

When short-pitch media is used, data may be written on a next RFID tag instead of the target RFID tag. As the location, where data is to be written, differs among RFID tag types, a check must be performed using the labels to be used to make sure that the data is written on the target RFID tags.

The RFID Analyze Tool can be used for this purpose.

11) Defective RFID Tag

Defective tags could be embedded while they are converted into labels, and the error rate differs depending on the tag types or the conversion methods.

Label manufacturers should mark such defective labels with something to indicate the tag is defective, or should prevent defective tags from being used.

Also, how to identify defective tags and good tags should be properly notified to end users.

12) PRINT POSITION ACCURACY

When using RFID tag embedded media, the print position accuracy may exceed the guaranteed tolerance of ±1 mm in all issue modes.

It is required to check the print position accuracy for each media type.

13) PAPER JAM ERROR

Depending on the type of glue or the flexibility of labels, a label may come unstuck in front of the sensor unit, which cause a paper jam. Particularly, the frequency of paper jam could become higher on the condition of low operating temperature or use of short-pitch labels.

It is required to check the media feed using the media to be used under the actual operating environment.

2-30

Image 46
Contents SX4T/SX5T Series Table of Contents Description of Model Number Printer SpecificationsX 4 T G S 1 0 Q Q R Front View/Rear View Appearance and Dimensions ApproximateDimensions Approximate Operation PanelBasic Specifications JAN8, EAN8, JAN13, EAN13, UPC-A, UPC-EMagnification of bar code Outline Electronics Specifications Specification of the MAIN4 PC Board Receive data line 1MB COM1 TCP/IP Home Position Strip Sensor Tr Print Head Print Head Media SX4TLabel Non Print Area Ribbon Care and Handling of the Media and Ribbon General Description Available Rfid TagLocation of Rfid Tag 40 mm + 5mm Media feeding direction Poor printing may occur in this area due to bump Improvement of Writing Accuracy Specification of Rfid TAG for B-SX704-RFID-U2-EU/AU-R 35 mm ±3 mm Short-pitch Tag Revision Date Apr Print quality on bumps is not guaranteed Print Position Accuracy Improvement of Writing Accuracy Specification of Rfid TAG for B-SX704-RFID-U2-US-R 35 mm ±3 mm Supply Specifications Rafsec Short Dipole2 Tag Supply Specifications Print quality on bumps is not guaranteed Print Position Accuracy Improvement of Writing Accuracy Specification of Rfid TAG for B-SX704-RFID-U2-CN-R 38 mm ±3 mm Short-pitch Tag Print quality on bumps is not guaranteed Print Position Accuracy Improvement of Writing Accuracy Optional KIT Strip Module B-9904-H-QM/QM-R option for the B-SX4T BUILT-IN LAN Interface Board B-9700-LAN-QM/QM-R Pcmcia Interface Board B-9700-PCM-QM/QM-RUSB Interface Board B-9700-USB-QM/QM-R Specification Rfid Module B-9704-RFID-U1-US/U1-EU/U1-EU-R/H1-QM/H1-QM-R10RFID Module B-SX704-RFID-U2-EU/AU/US/CN-R Applicable modelDSB-ASK Wireless LAN Board B-9700-WLAN-QM-R „ Hardware SpecificationCountry Code Table „ Country code„ MAC address „ LED „ Handling Precautions for B-9700-WLAN-QM „ Precautions„ Certification