Toshiba TOSVERT VF-FS1 Series Command & Setpoint selection Local/Remote, LIU007Z

Page 11

E6581373

3.6. Command & Setpoint selection (Local/Remote)

Indication to display Local/Remote mode is on the inverter unit (Refer to the inverter instruction manual for details). LONWORKS option command and setpoint are activated on Remote mode*1. LONWORKS option unit propagates the Local / Remote status to the network as the “Command from the network (bit5)” and “Setpoint from the network (bit6)” in “nvoStatusWord” network variable. Inverters have some switches to select the command and setpoint location. Following figure shows the diagram. Refer to the inverter instruction manual for the parameter in detail.

*1: Be careful that cmod command and fmod setpoint are activated for a short time just after the inverter power turned on. Set cmod and fmod to “Serial communication” to prevent this problem.

LIU007Z

cmod

Logic input = 48 (SC/LC)

Local/Remote key

Network cancel switch

Control Terminal

0

Operation Panel

1

1

Serial Comm.(LONWORKS)

2

Serial Comm.

Rem

Command

0

fmod

(LONWORKS)

Operation

Loc

Panel

VIA

1

VIB

2

Operation Panel

3

1

Serial Comm. (LONWORKS)

4

Serial Comm.

Rem

Setpoint

0

UP/DOWN

5

(LONWORKS)

Operation

Loc

Panel

- 10 -

Image 11

Contents E6581373 Handling in general IntroductionTable of Contents E6581373 Applicable model System configurationScope OverviewLIU007Z for VF-FS1 Names and functions of main partsOutline view LIU006ZLED DiagnosticsService LED OFF Fault LEDStatus LED LED on LED OFFRS485 communication port Neuron ID ConfigurationsService pin Device interface XIF file Inverter configurationsLIU007Z Command & Setpoint selection Local/RemoteReference parameter of the inverter Object id Functional profileFunctional profile supported by this option Network variables Node Object Node Object functional blockObject map NviRequest Object Request NciLocation Location LabelNvoStatus Object Status Object map is the following ACMotorDrive functional blockLIU Network variable list VSD601011Network variable list the other NciMinSpeed Minimum Speed Configuration propertiesNciMaxSpeed Maximum Speed NciMinOutTm Minimum Send Time NciRcvHrtBt Receive Heartbeat TimeNciSndHrtBt Send Heartbeat Time NciRampUpTm Ramp Up Time NciNmlSpeed Nominal Motor Speed in min-1NciNmlFreq Nominal Motor Frequency NciRampDownTm Ramp Down Time NciDrvSpeedScale Default value for nviDrvSpeedScaleNciPwUpOutTm Power up delay time NviDrvSpeedScale Drive Speed Setpoint Scaling NviResetFault Fault Reset CommandInput network variables NviDrvSpeedStpt Drive Speed SetpointLIU007Z LIU006Z NviInvSetFreq Frequency SetpointNviRelay1 /nviDigitalOut1,2 Control of Digital Output NviDigitalOutput Control of All Digital OutputsNviEmergOverride Emergency stop NviAnalogOut1,2 Control of Analog outputLnlearnvalue NviParamCmd Parameter accessLnrecall LnlearncurrentOutput network variables NvoStatusWord Inverter Status NvoDrvAlarm AlarmNvoDrvFeedback Velocity Feedback NvoTorque Motor Torque Monitor NvoAlarmWord Alarm StatusNvoDrvThermal Drive Thermal State NvoMotorThermal Motor Thermal StateNvoDigitalIn1 to 8 Digital Input Monitor NvoDrvEnergy Cumulative Input EnergyNvoDigitalInput All Digital Inputs Monitor NvoEmergStatus Emergency Status NvoAnalogIn1 to 3 Analog Input MonitorToshiba NvoParamResp Parameter Access ResponseNvoTypeVer Identification AsciiBinding ProcedureOption unit reset method Example usageCommunication health management Parameter access method E6581373 ANSI/EIA/CEA Specifications