Toshiba TOSVERT VF-FS1 Series instruction manual NviAnalogOut1,2 Control of Analog output

Page 26

E6581373

- Valid range

Bit

 

LIU007Z

 

 

LIU006Z

Terminal

 

Parameter

Terminal

Parameter

 

 

0

---

 

---

 

 

 

 

1

---

 

---

 

 

 

 

2

---

 

---

 

 

 

 

 

 

Under

Development

 

3

---

 

---

 

 

4

---

 

---

 

 

 

 

 

 

 

 

 

5

---

 

---

 

 

 

 

6-15

---

 

---

 

 

 

 

If multiple digital output control signals are used at the same time, the output value is the OR of all digital output controls.

6.5.7. nviAnalogOut1,2 (Control of Analog output)

Input network variable (Reserved) SNVT type: SNVT_lev_percent (81) They enable the analog output control.

- Valid range: 0.000 to 100.000%

(Output value is not adjusted by the inverter parameter “fm”, ”am”) - Unit: 0.005% (The resolution depends on the inverter specification)

When the variables will be used, the inverter parameters must be assigned.

Name

LIU007Z

 

LIU006Z

Terminal

Parameter

 

Terminal

 

Parameter

 

 

 

 

 

nviAnalogOut1

---

---

 

Under

Development

 

nviAnalogOut2

---

---

 

 

 

 

 

 

 

 

 

 

6.5.8. nviEmergOverride (Emergency stop)

Input network variable

SNVT type: SNVT_have_emerg (103)

It provides an emergency stop of the motor. Emergency stop can be configured by Emergency stop selection (f603) to coast stop, slow down stop or emergency DC braking (refer to the inverter instruction manual for details).

- Valid range

Value

Command

Description

0

Remove emergency

EMERG_NORMAL (No Emergency mode)

1

 

EMERG_PRESSURIZE (Emergency pressurize mode)

2

 

EMERG_DEPRESSURIZE (Emergency depressurize mode)

3

Emergency stop

EMERG_PURGE (Emergency purge mode)

4

EMERG_SHUTDOWN (Emergency shutdown mode)

 

5

 

EMERG_FIRE (Emergency fire mode)

6 to 255

 

---

N.B.: “Remove emergency” command clears a fault and resets the inverter.

- 25 -

Image 26
Contents E6581373 Introduction Handling in generalTable of Contents E6581373 Overview System configurationScope Applicable modelLIU006Z Names and functions of main partsOutline view LIU007Z for VF-FS1LED DiagnosticsService LED LED on LED OFF Fault LEDStatus LED OFFRS485 communication port Inverter configurations ConfigurationsService pin Device interface XIF file Neuron IDCommand & Setpoint selection Local/Remote LIU007ZReference parameter of the inverter Object id Functional profileFunctional profile supported by this option Network variables Node Object Node Object functional blockObject map NciLocation Location Label NviRequest Object RequestNvoStatus Object Status ACMotorDrive functional block Object map is the followingNetwork variable list VSD601011 LIUNetwork variable list the other NciMinSpeed Minimum Speed Configuration propertiesNciMaxSpeed Maximum Speed NciMinOutTm Minimum Send Time NciRcvHrtBt Receive Heartbeat TimeNciSndHrtBt Send Heartbeat Time NciRampUpTm Ramp Up Time NciNmlSpeed Nominal Motor Speed in min-1NciNmlFreq Nominal Motor Frequency NciRampDownTm Ramp Down Time NciDrvSpeedScale Default value for nviDrvSpeedScaleNciPwUpOutTm Power up delay time NviDrvSpeedStpt Drive Speed Setpoint NviResetFault Fault Reset CommandInput network variables NviDrvSpeedScale Drive Speed Setpoint ScalingNviDigitalOutput Control of All Digital Outputs NviInvSetFreq Frequency SetpointNviRelay1 /nviDigitalOut1,2 Control of Digital Output LIU007Z LIU006ZNviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stopLnlearncurrent NviParamCmd Parameter accessLnrecall LnlearnvalueOutput network variables NvoStatusWord Inverter Status NvoDrvAlarm AlarmNvoDrvFeedback Velocity Feedback NvoMotorThermal Motor Thermal State NvoAlarmWord Alarm StatusNvoDrvThermal Drive Thermal State NvoTorque Motor Torque MonitorNvoDigitalIn1 to 8 Digital Input Monitor NvoDrvEnergy Cumulative Input EnergyNvoDigitalInput All Digital Inputs Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency StatusAscii NvoParamResp Parameter Access ResponseNvoTypeVer Identification ToshibaExample usage ProcedureOption unit reset method BindingCommunication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA