Toshiba TOSVERT VF-FS1 Series instruction manual Reference parameter of the inverter

Page 12

E6581373

3.7. Reference parameter of the inverter

Reference parameter of the inverter is listed below.

Title

 

Name

Description

acc

 

Acceleration time

 

dec

 

Deceleration time

 

fh

 

Maximum frequency

Do not change these parameters, because

ul

 

Upper limit frequency

the LONWORKS option unit using them.

ll

 

Lower limit frequency

 

vl

 

Base frequency 1

 

 

 

 

Network command has priority when the

cmod

 

Command mode selection

inverter is Remote mode. (See previous

 

 

 

section)

 

 

 

Network setpoint has priority when the

fmod

 

Setpoint mode selection

inverter is Remote mode. (See previous

 

 

 

section)

f111

...

Logic input terminal function

Set proper value if use (See the inverter

instruction manual).

 

 

 

f603

 

Emergency stop selection

For “nviEmergOverride”

f800

 

Communication baud rate

Set “1” (default)

f801

 

Communication parity

Set “1” (default)

f803

 

Communication error trip time

Set properly value

f829

 

Communication protocol

Set “1” (MODBUS)

 

 

 

 

f851

 

Operation at network disconnection

See “section 7.4 Communication health

 

management”.

 

 

 

Warning

Mandatory

For LIU007Z, set up “Communication error trip function (f803, see the inverter instruction manual for details)” to stop the inverter when this option unit is deactivated by an unusual event such as tripping, an operating error, power outage, failure, etc. Deactivated option unit may cause an accident, if the “Communication error trip function” is not properly set up.

- 11 -

Image 12
Contents E6581373 Introduction Handling in generalTable of Contents E6581373 System configuration ScopeOverview Applicable modelNames and functions of main parts Outline viewLIU006Z LIU007Z for VF-FS1Diagnostics Service LEDLED Fault LED Status LEDLED on LED OFF OFFRS485 communication port Configurations Service pin Device interface XIF fileInverter configurations Neuron IDCommand & Setpoint selection Local/Remote LIU007ZReference parameter of the inverter Functional profile Functional profile supported by this optionObject id Node Object functional block Object mapNetwork variables Node Object NciLocation Location Label NviRequest Object RequestNvoStatus Object Status ACMotorDrive functional block Object map is the followingNetwork variable list VSD601011 LIUNetwork variable list the other Configuration properties NciMaxSpeed Maximum SpeedNciMinSpeed Minimum Speed NciRcvHrtBt Receive Heartbeat Time NciSndHrtBt Send Heartbeat TimeNciMinOutTm Minimum Send Time NciNmlSpeed Nominal Motor Speed in min-1 NciNmlFreq Nominal Motor FrequencyNciRampUpTm Ramp Up Time NciDrvSpeedScale Default value for nviDrvSpeedScale NciPwUpOutTm Power up delay timeNciRampDownTm Ramp Down Time NviResetFault Fault Reset Command Input network variablesNviDrvSpeedStpt Drive Speed Setpoint NviDrvSpeedScale Drive Speed Setpoint ScalingNviInvSetFreq Frequency Setpoint NviRelay1 /nviDigitalOut1,2 Control of Digital OutputNviDigitalOutput Control of All Digital Outputs LIU007Z LIU006ZNviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stopNviParamCmd Parameter access LnrecallLnlearncurrent LnlearnvalueOutput network variables NvoDrvAlarm Alarm NvoDrvFeedback Velocity FeedbackNvoStatusWord Inverter Status NvoAlarmWord Alarm Status NvoDrvThermal Drive Thermal StateNvoMotorThermal Motor Thermal State NvoTorque Motor Torque MonitorNvoDrvEnergy Cumulative Input Energy NvoDigitalInput All Digital Inputs MonitorNvoDigitalIn1 to 8 Digital Input Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency StatusNvoParamResp Parameter Access Response NvoTypeVer IdentificationAscii ToshibaProcedure Option unit reset methodExample usage BindingCommunication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA