Toshiba TOSVERT VF-FS1 Series NciNmlSpeed Nominal Motor Speed in min-1, NciRampUpTm Ramp Up Time

Page 22

E6581373

6.4.6. nciNmlSpeed (Nominal Motor Speed in min-1)

Configuration property, Variable Speed Drive 6010_11 (Mandatory)

SNVT type: SNVT_rpm (102)

SCPT reference: SCPTnomRPM (158)

It is used to provide the nominal speed of the inverter output in min-1.

-Valid range: 0 to 65534 min-1

-Unit: 1 min-1

-Default value: 1800 min-1

Danger

Prohibited

Do not change this value while the motor is running.

Otherwise, It may result in injuries by motor running with unexpected speed. Do not set the value out of valid range.

Otherwise, It may result in injuries by motor running with unexpected speed.

6.4.7. nciNmlFreq (Nominal Motor Frequency)

Configuration property, Variable Speed Drive 6010_11 (Mandatory) SNVT type: SNVT_freq_hz (76)

SCPT reference: SCPTnomFreq (159)

This configuration property is used to provide the nominal speed of the inverter output in Hz. This is used as the base speed on ACMotorDrive functional block. It should be set to Rated Frequency of motor.

-Valid range: 25.0 to 200.0 Hz

-Unit: 0.1 Hz

-Default value: 60.0 Hz

N.B.: By editing this variable, this option unit changes the inverter parameter “vl” automatically.

Danger

Prohibited

Do not change this value while the motor is running.

Otherwise, It may result in injuries by motor running with unexpected speed. Do not set the value out of valid range.

Otherwise, It may result in injuries by motor running with unexpected speed.

6.4.8. nciRampUpTm (Ramp Up Time)

Configuration property, Variable Speed Drive 6010_11 (Mandatory)

SNVT type: SNVT_time_sec (107)

SCPT reference: SCPTrampUpTm (160)

It determines the ramp up time of the motor.

-Valid range: 0.1 to 3200.0 sec.

-Unit: 0.1 sec.

-Default value: 10.0 sec.

N.B.: By editing this variable, this option unit changes the inverter parameter “acc” automatically.

- 21 -

Image 22

Contents E6581373 Introduction Handling in generalTable of Contents E6581373 Overview System configurationScope Applicable modelLIU006Z Names and functions of main partsOutline view LIU007Z for VF-FS1Service LED DiagnosticsLED LED on LED OFF Fault LEDStatus LED OFFRS485 communication port Inverter configurations ConfigurationsService pin Device interface XIF file Neuron IDCommand & Setpoint selection Local/Remote LIU007ZReference parameter of the inverter Functional profile supported by this option Functional profileObject id Object map Node Object functional blockNetwork variables Node Object NciLocation Location Label NviRequest Object RequestNvoStatus Object Status ACMotorDrive functional block Object map is the followingNetwork variable list VSD601011 LIU Network variable list the other NciMaxSpeed Maximum Speed Configuration propertiesNciMinSpeed Minimum Speed NciSndHrtBt Send Heartbeat Time NciRcvHrtBt Receive Heartbeat TimeNciMinOutTm Minimum Send Time NciNmlFreq Nominal Motor Frequency NciNmlSpeed Nominal Motor Speed in min-1NciRampUpTm Ramp Up Time NciPwUpOutTm Power up delay time NciDrvSpeedScale Default value for nviDrvSpeedScaleNciRampDownTm Ramp Down Time NviDrvSpeedStpt Drive Speed Setpoint NviResetFault Fault Reset CommandInput network variables NviDrvSpeedScale Drive Speed Setpoint ScalingNviDigitalOutput Control of All Digital Outputs NviInvSetFreq Frequency SetpointNviRelay1 /nviDigitalOut1,2 Control of Digital Output LIU007Z LIU006ZNviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stopLnlearncurrent NviParamCmd Parameter accessLnrecall LnlearnvalueOutput network variables NvoDrvFeedback Velocity Feedback NvoDrvAlarm AlarmNvoStatusWord Inverter Status NvoMotorThermal Motor Thermal State NvoAlarmWord Alarm StatusNvoDrvThermal Drive Thermal State NvoTorque Motor Torque MonitorNvoDigitalInput All Digital Inputs Monitor NvoDrvEnergy Cumulative Input EnergyNvoDigitalIn1 to 8 Digital Input Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency StatusAscii NvoParamResp Parameter Access ResponseNvoTypeVer Identification ToshibaExample usage ProcedureOption unit reset method BindingCommunication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA