Toshiba TOSVERT VF-FS1 Series instruction manual Specifications, Ansi/Eia/Cea

Page 38

E6581373

8. Specifications

	Item	Specification		Notes
	Number of domains	2
	Number of address	37
	entries	37
	entries
	Number of alias tables	8
	Communication	Free topology transceiver	ANSI/EIA/CEA 709.3
	transceiver	TP/FT-10 channel type.	ANSI/EIA/CEA 709.3
	transceiver	TP/FT-10 channel type.
	Baudrate	78kbps
	Protocol	LonTalk	ANSI/EIA 709.1
	Communication signal	2 wires plus shield	NETA, Sheild, NETB
		Free topology:
		Between devices: 400m or less	When recommended cable is used:
	Transmission distance	Total cable length: 500m or less	When recommended cable is used:
	Transmission distance	Bus topology ( both terminated):	Level 4/22AWG
		Bus topology ( both terminated):	Level 4/22AWG
		Total cable length: 1400m or less
		Stub length: 3m or less
	Functional block	Node Object (0)	LONMARK functional profile
	Functional block	Variable Speed Motor Drive (1)	Variable Speed Motor Drive
		Variable Speed Motor Drive (1)	Variable Speed Motor Drive
	Number of	Input network variables: 8
	Number of	Output network variables: 17
	Network variables	Output network variables: 17
	Network variables	Configuration properties: 12
		Configuration properties: 12
	Number of connected	64 nodes at maximum	However, a	host and routers are
	nodes	64 nodes at maximum	counted as one node.
	nodes		counted as one node.
	Service pin function	Mechanical switch (SW2)	Used for notification of Neuron ID to
	Service pin function	Mechanical switch (SW2)	the host.
			the host.
			Applicable terminal block
	Terminal block	Detachable terminal block 3-pole	Manufacturer: PHOENIX CONTACT
			Type-Form	: MSTB 2,5/3-ST-5,08

- 37E -

Image 38

Contents E6581373 Introduction Handling in generalTable of Contents E6581373 Overview System configurationScope Applicable modelLIU006Z Names and functions of main partsOutline view LIU007Z for VF-FS1LED DiagnosticsService LED LED on LED OFF Fault LEDStatus LED OFFRS485 communication port Inverter configurations ConfigurationsService pin Device interface XIF file Neuron IDCommand & Setpoint selection Local/Remote LIU007ZReference parameter of the inverter Object id Functional profileFunctional profile supported by this option Network variables Node Object Node Object functional blockObject map NciLocation Location Label NviRequest Object RequestNvoStatus Object Status ACMotorDrive functional block Object map is the followingNetwork variable list VSD601011 LIUNetwork variable list the other NciMinSpeed Minimum Speed Configuration propertiesNciMaxSpeed Maximum Speed NciMinOutTm Minimum Send Time NciRcvHrtBt Receive Heartbeat TimeNciSndHrtBt Send Heartbeat Time NciRampUpTm Ramp Up Time NciNmlSpeed Nominal Motor Speed in min-1NciNmlFreq Nominal Motor Frequency NciRampDownTm Ramp Down Time NciDrvSpeedScale Default value for nviDrvSpeedScaleNciPwUpOutTm Power up delay time NviDrvSpeedStpt Drive Speed Setpoint NviResetFault Fault Reset CommandInput network variables NviDrvSpeedScale Drive Speed Setpoint ScalingNviDigitalOutput Control of All Digital Outputs NviInvSetFreq Frequency SetpointNviRelay1 /nviDigitalOut1,2 Control of Digital Output LIU007Z LIU006ZNviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stopLnlearncurrent NviParamCmd Parameter accessLnrecall LnlearnvalueOutput network variables NvoStatusWord Inverter Status NvoDrvAlarm AlarmNvoDrvFeedback Velocity Feedback NvoMotorThermal Motor Thermal State NvoAlarmWord Alarm StatusNvoDrvThermal Drive Thermal State NvoTorque Motor Torque MonitorNvoDigitalIn1 to 8 Digital Input Monitor NvoDrvEnergy Cumulative Input EnergyNvoDigitalInput All Digital Inputs Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency StatusAscii NvoParamResp Parameter Access ResponseNvoTypeVer Identification ToshibaExample usage ProcedureOption unit reset method BindingCommunication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA