Toshiba TOSVERT VF-FS1 Series Input network variables, NviDrvSpeedStpt Drive Speed Setpoint

Page 24

E6581373

6.5. Input network variables

6.5.1. nviDrvSpeedStpt (Drive Speed Setpoint)

Input network variable, Variable Speed Drive 6010_11 (Mandatory) SNVT type: SNVT_switch (95)

It provides start/stop control and a low resolution speed setpoint as a percent of nominal speed. Output frequency = “nciNmlFreq” x “nviDrvSpeedStpt.value” x “nviDrvSpeedScale”

- Valid range

	nviDrvSpeedStpt		Operation
	value	state	Operation
	value	state
	N/A	0	Stop
	0.0 to 100.0%	1	Drive at the speed from 0.5% to 100%
	100.5 to 127.5%	1	Drive at 100% speed
	N/A	-1	AUTO (Invalid)

- Unit (nviDrvSpeedStpt.value): 0.5%

- Default value: 0.0% (value), AUTO (state = -1),

Default value will be adopted at power-up and in case of not receiving an update of “nviSpeedStpt”, “nviDrvSpeedScale” or “nviInvSetFreq” within the specified Receive Heartbeat time (nciRcvHrtBt). Speed reference set by “nviInvSetFreq” will override “nviDrvSpeedStpt” (refer to “nviInvSetFreq”).

N.B. The value exceeded to the inverter setpoint resolution will be rounded.

6.5.2. nviDrvSpeedScale (Drive Speed Setpoint Scaling)

Input network variable, Variable Speed Drive 6010_11 (Optional) SNVT type: SNVT_lev_percent (81)

This input network variable provides scaling for “nviDrvSpeedStpt”. Negative values indicate a motor direction in reverse.

-Valid range: -163.840 to 163.830%

-Unit: 0.005%

-Default value: “nciDrvSpeedScale”

Default value will be adopted at power-up and in case of not receiving an update of “nviSpeedStpt”, “nviDrvSpeedScale” or “nviInvSetFreq” within the specified Receive Heartbeat time (nciRcvHrtBt).

N.B. The value exceeded to the inverter setpoint resolution will be rounded.

6.5.3. nviResetFault (Fault Reset Command)

Input network variable

SNVT type: SNVT_switch (95)

This command clears the inverter fault when the inverter is under a fault that can be cleared. - Valid range

nviResetFault			Command
value		state

N/A		0, -1	Invalid
0.0%		1

0.5% to 127.5%		1	Clear a fault and reset the inverter.

- 23 -

Image 24

Contents E6581373 Introduction Handling in generalTable of Contents E6581373 System configuration ScopeOverview Applicable modelNames and functions of main parts Outline viewLIU006Z LIU007Z for VF-FS1Diagnostics Service LEDLED Fault LED Status LEDLED on LED OFF OFFRS485 communication port Configurations Service pin Device interface XIF fileInverter configurations Neuron IDCommand & Setpoint selection Local/Remote LIU007ZReference parameter of the inverter Functional profile Functional profile supported by this optionObject id Node Object functional block Object mapNetwork variables Node Object NciLocation Location Label NviRequest Object RequestNvoStatus Object Status ACMotorDrive functional block Object map is the followingNetwork variable list VSD601011 LIUNetwork variable list the other Configuration properties NciMaxSpeed Maximum SpeedNciMinSpeed Minimum Speed NciRcvHrtBt Receive Heartbeat Time NciSndHrtBt Send Heartbeat TimeNciMinOutTm Minimum Send Time NciNmlSpeed Nominal Motor Speed in min-1 NciNmlFreq Nominal Motor FrequencyNciRampUpTm Ramp Up Time NciDrvSpeedScale Default value for nviDrvSpeedScale NciPwUpOutTm Power up delay timeNciRampDownTm Ramp Down Time NviResetFault Fault Reset Command Input network variablesNviDrvSpeedStpt Drive Speed Setpoint NviDrvSpeedScale Drive Speed Setpoint ScalingNviInvSetFreq Frequency Setpoint NviRelay1 /nviDigitalOut1,2 Control of Digital OutputNviDigitalOutput Control of All Digital Outputs LIU007Z LIU006ZNviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stopNviParamCmd Parameter access LnrecallLnlearncurrent LnlearnvalueOutput network variables NvoDrvAlarm Alarm NvoDrvFeedback Velocity FeedbackNvoStatusWord Inverter Status NvoAlarmWord Alarm Status NvoDrvThermal Drive Thermal StateNvoMotorThermal Motor Thermal State NvoTorque Motor Torque MonitorNvoDrvEnergy Cumulative Input Energy NvoDigitalInput All Digital Inputs MonitorNvoDigitalIn1 to 8 Digital Input Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency StatusNvoParamResp Parameter Access Response NvoTypeVer IdentificationAscii ToshibaProcedure Option unit reset methodExample usage BindingCommunication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA