Toshiba B-852-TS12-QP owner manual Spacer Supply Holder

Page 19

2. PRINTER SETUP

ENGLISH VERSION EO1-33028

2.7 Loading the Media

2.7.1Installing the Media onto the Supply Holder Unit (Cont.)

WARNING!

If you turn the Removable Supply Holder side down after loading the media, the media may drop by weight. You might be injured by the dropped media.

CAUTION!

When installing the media roll, do not push on the Non-removable Supply Holder as this will result in the media roll not being properly centred.

NOTES:

1.This Supply Holder accepts four sizes of media core: 38 mm, 40 mm, 42 mm and

76.2 mm.. When using a media roll of 38 mm, 40 mm, or 42 mm, remove the spacers from the Supply Holders by pushing both hooks of the Spacer. Keep

the removed Spacers safe.

2

Spacer

1

1

Supply Holder

2.Use only inside wound label stock. Outside wound label stock may not feed properly. Use outside wound label stock at your own risk.

3.Do not over-tighten the green Supply Holder Locking Knob.

The diagram below, and the steps that follow, show the procedures for installing the Media onto the Supply Shaft and reassembling the Supply Holder Unit. Be sure to follow the step-by-step procedure exactly or the auto centering mechanism may not work properly.

 

Removable

 

Print Side

 

 

Supply Holder

4

 

 

Green Supply

 

 

 

 

Holder Locking

 

 

 

 

Knob

3

 

 

1

 

2

 

 

 

 

 

 

Tab

 

Slot

 

Non-removable

 

 

Supply Holder

 

 

 

 

 

 

 

Supply Shaft

Media Roll

 

 

 

 

Installing the Media and reassembling the Supply Holder

1.Place the media roll onto the Supply Shaft with the media feeding from the bottom as shown in the diagram above. c

2.Align the tab of the Removable Supply Holder with the Slot in the Supply Shaft, then reinstall the Removable Supply Holder by sliding it onto the Supply Shaft as shown in the figure above.

3.Holding the reassembled Supply Holder Unit in your right hand, apply

pressure only to the reinstalled Removable Supply Holder to push it in the direction of arrow d, causing the auto centering mechanism to center the media on the Supply Shaft.

4.Tighten the green Supply Holder Locking Knob for the Removable Supply Holder by turning it in the direction of arrow e.

5.Tighten the green Supply Holder Locking Knob for the Non- removable Supply Holder by turning it in the direction of arrow f .

E2- 8

Image 19
Contents 852-TS12-QP List of Standard of Conformity 852-TS12-QP 6DIHW\6XPPDU\ Request Regarding Maintenance PrecautionsTable of Contents EA3-1 E6-1EA1-1 EA2-1Product Overview Introduction FeaturesUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Installing the Media onto the Supply Holder UnitSpacer Supply Holder Printer Loading Media into the Printer Head Pressure Adjust Lever Setting the Black Mark Sensor Setting the Feed Gap SensorDisconnect the mains Loading the RibbonCOM Inserting the Optional Pcmcia CardsTest Print If necessary, the print test may now be repeated from step E2-17 Overview Printer OperationOperating Modes Operating Modes Operation Panel On Line ModeOperation Reset Restart key Dump ModePrint Conditions Cleaning MaintenancePrint Head/Platen/ Sensors Optional Cutter Module Covers and PanelsError Messages TroubleshootingPossible Problems Causes Solutions Possible ProblemsRemoving Jammed Media Feed key Threshold SettingA1.1 Printer Appendix 1 SpecificationsLabel A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples Appendix 4 Print Samples UPC-A Bar code GlossariesPre-printed media Index Index