Toshiba B-852-TS12-QP owner manual A1.3.2 Detection Area of the Transmissive Sensor

Page 43

APPENDIX 1 SPECIFICATIONS

ENGLISH VERSION EO1-33028

A1.3 Media

A1.3.1 Media Type (Cont.)

 

 

 

 

[Unit: mm]

 

 

 

 

 

 

Label dispensing mode

Batch mode

 

Cut mode

Item

 

 

 

 

c Minimum media pitch

15.0

 

Label: 38.0

 

Tag: 25.4

 

 

 

 

d Label length

Min. 12.5

 

Min. 32.0

e Width including backing paper

100.0- 242.0

 

100.0 – 235.0

f Gap length

2.5 – 20.0

 

6.0 – 20.0

g Black mark length (Tag paper)

 

2.0 – 10.0

h Effective print width

 

216.8±0.2

i Print speed up/slow down area

 

1.0

j Black mark length (Label)

Refer to NOTE 3 below.

Max. print length

 

640.0

Maximum effective length for on the fly issue

 

320.0

Max. outer roll diameter

 

φ230

Thickness

Label + backing paper

 

0.13 – 0.18

Tag

 

0.08 – 0.18

 

 

NOTES:

1.To ensure print quality and print head life use only TOSHIBA TEC specified media.

2.When using the cutter ensure that label length d plus inter-label gap length f exceeds 38 mm. (i.e. label pitch should be greater than 38 mm.)

3.When marking black marks on label rolls, the following requirements must be satisfied.

When the gap length is less than 4 mm:

The black mark length should be longer than the gap length. When the gap length is 4 mm or more:

The black mark should not overlap the gap for more than 4 mm and the following label.

4.“On the fly issue” means that the printer can feed and print without stopping between labels.

A1.3.2 Detection Area of the Transmissive Sensor

The transmissive sensor is movable from the center to the left edge of media.

The transmissive sensor detects a gap between labels, as illustrated below.

Sensor position

Area to be detected.

 

Center of media

 

 

 

 

 

 

 

 

 

 

 

Print side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. 2.0 mm

 

 

 

 

 

 

 

 

 

 

 

Label

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gap

 

 

 

 

 

 

 

 

 

 

 

 

(Min. 6.0 mm when using

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the cutter module.)

 

 

 

 

 

 

 

 

 

 

 

Label

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. 12 mm

 

 

 

 

 

 

 

 

Media feed direction

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sensor is movable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

within this range.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EA1- 3

Image 43
Contents 852-TS12-QP List of Standard of Conformity 852-TS12-QP 6DIHW\6XPPDU\ Request Regarding Maintenance PrecautionsTable of Contents EA3-1 E6-1EA1-1 EA2-1Product Overview Introduction FeaturesUnpacking Accessories Rear View DimensionsAppearance Front ViewInterior Operation PanelPrecautions Printer SetupProcedure before Operation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Installing the Media onto the Supply Holder UnitSpacer Supply Holder Printer Loading Media into the Printer Head Pressure Adjust Lever Setting the Black Mark Sensor Setting the Feed Gap SensorDisconnect the mains Loading the RibbonCOM Inserting the Optional Pcmcia CardsTest Print If necessary, the print test may now be repeated from step E2-17 Overview Printer OperationOperating Modes Operating Modes Operation Panel On Line ModeOperation Reset Restart key Dump ModePrint Conditions Cleaning MaintenancePrint Head/Platen/ Sensors Optional Cutter Module Covers and PanelsError Messages TroubleshootingPossible Problems Causes Solutions Possible ProblemsRemoving Jammed Media Feed key Threshold SettingA1.1 Printer Appendix 1 SpecificationsLabel A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceAppendix 4 Print Samples Appendix 4 Print Samples UPC-A Bar code GlossariesPre-printed media Index Index