Toshiba B-852-TS12-QP owner manual Operation Reset

Page 32

4.ON LINE MODE

ENGLISH VERSION EO1-33028

4.2 Operation

4.2 Operation

4.3 Reset

NOTE:

If the [RESTART] key is held for less than 3 seconds when the printer is in an error or pause state, the printer restarts printing. However, when a communication error or command error occurs, the printer returns to an idle condition.

When the printer is turned on, the ON LINEmessage appears on the LCD Message Display. It is shown during standby or normal printing.

1.The printer is turned on, standing by, or printing.

21￿/,1(￿

2.If any error occurs during printing, an error message appears. The printer stops printing automatically. (The number on the right column shows the number of unprinted media.)

12￿3$3(5￿￿￿￿￿￿￿￿

3.To clear the error, press the [RESTART] key. The printer resumes printing.

21￿/,1(￿

4. If the [PAUSE] key is pressed during printing, the printer stops printing temporarily. (The number on the right column shows the number of unprinted media.)

3$86(￿ ￿￿￿￿￿￿￿￿￿￿

5.When the [RESTART] key is pressed, the printer resumes printing.

21￿/,1(￿

Reset operation clears the print data sent to the printer from the computer, and returns the printer to an idle condition.

1.The printer is turned on, standing by, or printing.

21￿/,1(￿

2.To stop printing, or clear the data sent from the computer, press the [PAUSE] key. The printer stops printing.

3$86(￿ ￿￿￿

3.Press and hold the [RESTART] key for 3 seconds or longer.

￿￿!5(6(7￿

4.Press the [PAUSE] key. The data sent from the computer will be cleared, and the printer returns to an idle condition.

21￿/,1(￿

E4- 2

Image 32
Contents 852-TS12-QP List of Standard of Conformity 852-TS12-QP 6DIHW\6XPPDU\ Precautions Request Regarding MaintenanceTable of Contents E6-1 EA1-1EA2-1 EA3-1Unpacking Introduction FeaturesProduct Overview Accessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Installing the Media onto the Supply Holder Unit Loading the MediaSpacer Supply Holder Printer Loading Media into the Printer Head Pressure Adjust Lever Setting the Feed Gap Sensor Setting the Black Mark SensorLoading the Ribbon Disconnect the mainsInserting the Optional Pcmcia Cards COMTest Print If necessary, the print test may now be repeated from step E2-17 Operating Modes Printer OperationOverview Operating Modes On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter ModuleTroubleshooting Error MessagesPossible Problems Possible Problems Causes SolutionsRemoving Jammed Media Threshold Setting Feed keyAppendix 1 Specifications A1.1 PrinterA1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 Print Samples Appendix 4 Print Samples UPC-A Glossaries Bar codePre-printed media Index Index