Toshiba B-852-TS12-QP owner manual Threshold Setting, Feed key

Page 40

6. TROUBLESHOOTING

ENGLISH VERSION EO1-33028

6.4 Threshold Setting

6.4 Threshold Setting

NOTES:

1.If the [PAUSE] key is released within 3 seconds whilst in pause state, paper will not feed.

2.Failure to feed more than 1.5 labels may result in an incorrect threshold setting.

3.While the Print Head Block is raised, the [PAUSE] key does not work.

4.Errors such as paper end and cutter error are not detected during paper feed.

5.Selecting the Transmissive Sensor(for pre-printed labels) within software commands allows the printer to detect the proper print start position correctly even when using pre-printed labels.

6.If the printer continued to print out of position after setting the threshold, adjust the Feed Gap Sensor in the system mode. Reset the threshold again. Make sure that the Transmissive Sensor (for pre-printed labels) is selected in the feed and issue commands.

To maintain a constant print position the printer uses the Transmissive Sensor to detect the gap between labels by measuring the amount of light passing through the media. When the media is pre-printed, the darker (or more dense) inks can interfere with this process causing paper jam errors. To get around this problem a minimum threshold can be set for the sensor in the following way.

„￿Threshold setting procedure

1.Turn the power ON. The printer is in stand by mode.

21￿/,1(￿

2.Load a media roll.

3.Press the [PAUSE] key.

3$86(￿

4.The printer enters the pause mode.

5.Press and hold the [PAUSE] key for at least 3 seconds in the pause state.

75$160,66,9(￿

6.The sensor type is displayed.

7.To select the Reflective Sensor (Black Mark Sensor), press the

[FEED] key.

5()/(&7,9(￿

8.To select the Transmissive Sensor (Feed Gap Sensor), press the [FEED] key again.

75$160,66,9(￿

9.Press and hold the [PAUSE] key until more than 1.5 labels (tags) have been advanced.

The media is advanced until the [PAUSE] key is released. (Threshold setting is completed by this operation.)

3$86(￿

10.Press the [RESTART] key.

21￿/,1(￿

11.The printer is in stand-by.

12.Send an issue command from the PC to the printer.

21￿/,1(￿

E6- 4

Page 39 Page 41
Image 40
Page 39 Page 41
Contents 852-TS12-QP List of Standard of Conformity 852-TS12-QP 6DIHW\6XPPDU\ Precautions Request Regarding MaintenanceTable of Contents E6-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesUnpacking Accessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Loading the MediaSpacer Supply Holder Printer Loading Media into the Printer Head Pressure Adjust Lever Setting the Feed Gap Sensor Setting the Black Mark SensorLoading the Ribbon Disconnect the mainsInserting the Optional Pcmcia Cards COMTest Print If necessary, the print test may now be repeated from step E2-17 Overview Printer OperationOperating Modes Operating Modes On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter ModuleTroubleshooting Error MessagesPossible Problems Possible Problems Causes SolutionsRemoving Jammed Media Threshold Setting Feed keyAppendix 1 Specifications A1.1 PrinterA1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 Print Samples Appendix 4 Print Samples UPC-A Glossaries Bar codePre-printed media Index Index
Top Page Image Contents