APPENDIX 2 MESSAGES AND LEDS
ENGLISH VERSION
APPENDIX 2 MESSAGES AND LEDS
APPENDIX 2 MESSAGES AND LEDS
Appendix 4 describes the LCD messages displayed on the operation panel.
Symbols in the message
1:•: The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.
2:****: the number of unprinted media. Up to 9999 (in pieces)
3:%%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)
4:###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)
5:&&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)
|
| LED Indication |
| Restoration | Acceptance of | |
|
|
|
| by RESTART | Status Request | |
No. | LCD Message | Printer Status | ||||
key Yes/No | Reset Command | |||||
|
| POWER ONLINE ERROR |
|
| Yes/No | |
|
|
|
|
| ||
1 | ON LINE |
| • | • | z | In online mode | Yes | |
ON LINE |
| • | ~ | z | In online mode (The printer in | Yes | ||
|
| communication) |
|
| ||||
2 | HEAD OPEN |
| • | z | z | The print head block is opened in online | Yes | |
| mode. |
|
| |||||
3 | PAUSE **** |
| • | z | z | The printer is paused. | Yes | Yes |
4 |
|
|
|
|
| A parity, overrun, or framing error has | Yes | Yes |
COMMS ERROR | • | z | • | occurred during communication through |
|
| ||
|
|
|
|
|
| the |
|
|
5 | PAPER JAM | **** | • | z | • | The media is jammed during paper feed. | Yes | Yes |
6 | CUTTER ERROR**** | • | z | • | A problem has occurred with the cutter | Yes | Yes | |
module. |
|
| ||||||
7 |
|
|
|
|
| The media has run out, or the media is | Yes | Yes |
NO PAPER | **** | • | z | • | not loaded on the supply holder |
|
| |
|
|
|
|
|
| properly. |
|
|
|
|
|
|
|
| The ribbon has run out, or has been torn. | Yes | Yes |
8 | RIBBON ERROR**** | • | z | • | A problem has occurred with the sensor |
|
| |
that determines the torque for the ribbon |
|
| ||||||
|
|
|
|
|
| motor. |
|
|
9 | HEAD OPEN | **** | • | z | • | Feed or printing was attempted with the | Yes | Yes |
print head block open. |
|
| ||||||
10 | EXCESS HEAD TEMP | • | z | • | The print head is overheated. | No | Yes | |
| SAVING%%%%%%% |
|
|
| In writable character or PC command | Yes | ||
11 | or |
| • | • | z | save mode |
|
|
| SAVING ###&&&& |
|
|
|
|
|
| |
12 | FLASH WRITE ERR. | • | z | • | An error has occurred while writing to | No | Yes | |
flash memory or ATA card. |
|
| ||||||
13 |
|
|
|
|
| An erase error has occurred in | No | Yes |
FORMAT ERROR | • | z | • | formatting the flash memory or ATA |
|
| ||
|
|
|
|
|
| card. |
|
|
14 | FLASH CRD FULL | • | z | • | Data cannot be stored because the flash | No | Yes | |
memory or ATA card is full. |
|
| ||||||
15 | HEAD ERROR | • | z | • | There is a problem with the print head. | Yes | Yes | |
16 | Display of error | • | z | • | A command error has occurred in | Yes | Yes | |
| message (See Notes.) |
|
|
| analyzing the command. |
|
| |
EA2- 1